2 1-800-732-2677
www.petsafe.net 3
This PetSafe
®
Stubborn Dog In-Ground Fence
™
is not a solid barrier. This system is designed to act as a deterrent
to remind pets by Static Correction to remain in the boundary established. It is important that you reinforce training
with your pet on a regular basis. Proper fit of the collar is important. A collar worn for too long or made too tight
on the pet’s neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly
known as bed sores.
• Avoid leaving the collar on the dog for more than 12 hours per day.
• When possible reposition the collar on the pet’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the electronic collar; it will cause excessive pressure on the contacts.
• When using a separate collar for a lead, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Examine the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed.
• If the condition persists beyond 48 hours, see your veterinarian.
• For additional information on bed sores and pressure necrosis, please visit our website.
These steps will help keep your pet safe and comfortable. Millions of pets are comfortable while they wear
stainless steel contacts. Some pets are sensitive to contact pressure. You may find after some time that your pet is
very tolerant of the collar. If so, you may relax some of these precautions. It is important to continue daily checks of
the contact area. If redness or sores are found, discontinue use until the skin has fully healed.
You may need to trim the hair in the area of the Contact Points. Never shave the dog’s neck; this may lead to a
rash or infection.
• The Receiver Collar should not be on your dog when the system is tested. Your pet may receive an
unintended correction.
• The Boundary Width of the system must be tested whenever an adjustment is made to the
containment field to prevent unintended corrections to your pet.
• If you use a collar and leash for training, be sure the extra collar does not put pressure on the contact
points.
• Always remove your dog’s Receiver Collar before performing any Transmitter testing.
• If possible, DO NOT use an AC circuit protected with a Ground Fault Circuit Interrupter (GFCI) or
Residual Current Device (RCD). In rare cases, nearby lightning strikes may cause the GFCI or RCD to
trip. Without power your dog may be vulnerable to escape. You will have to reset the GFCI or RCD to
restore power to the system.
• Do not install the Surge Protector if there is not at least 30 feet (10 meters) or more of wire between
the electrical outlet and electrical service panel.
• Plug the Surge Protector into a grounded (3-prong) outlet that is within 5 feet of the Fence
Transmitter. ALWAYS use a grounded (3-prong) outlet to ensure maximum protection.
• Do not remove the ground prong from the Surge Protector plug. Do not use a 3-prong plug to
2-prong outlet converter. Doing so will make the Surge Protector ineffective against surges or spikes.
• Use care when mowing or trimming your grass not to cut the loop wire.
• Verify that the boundary loop and Transmitter wires connect to the proper Surge Protector terminals.
Reversed connections will result in an increased risk of surge related damage.
• For added protection, when unused for long periods of time or prior to thunderstorms, unplug from
the wall outlet and disconnect the loop boundary wires. This will prevent damage to the transmitter
due to surges.
• To prevent an unintended correction, after the Boundary Flags have been placed, be sure to set the
static correction on the receiver collar back to level 1 tone only.
Summary of Contents for PIG00-100777
Page 31: ...www petsafe net 31...
