PerkinElmer Lambda 650 Hardware Manual Download Page 69

Page: 69 / 72

Lambda 650/850/950 Hardware Guide . 69

Accessory Connector Panel

The accessory panel is fitted with an RS 232 interface and two 15-pin connector sockets.

There are also three slots for the accessory printed circuit boards (PCB) for those accessories

that require them.

Figure 28 Connector Panel for Accessories

NOTE:

The insulation of externally connected accessories should meet the requirements of IEC

61010-1 or IEC 60950.

Figure 29 Possible accessories for a Lambda 650/850/950

Sites for accessory PCBs

15-Pin Accessory Sockets marked
ACCESSORY 1 on the left and ACCESSORY 2
on the right (15 way HD D-type, maximum
voltage -12 to +24 V)

RS 232 Interface Socket marked
COMPUTER (25 way D-type,
maximum voltage ± 12 V

Peltier Cell Holder

Peltier Cell Changer

Temperature Sensor

Automatic Cell Changer

Sipper

External
Printer

Summary of Contents for Lambda 650









































































Search results

Summary of Contents for Lambda 650

Reviews:

Brands by name

Popular brands

PerkinElmer Lambda 650, Hardware Manual

Search results

Summary of Contents for Lambda 650

Reviews:

Brands by name

Popular brands