manualshive.com logo in svg

PerkinElmer Lambda 650, Hardware Manual

Share
Download
PerkinElmer Lambda 650 Hardware Manual Download Page 46

46 . Using the Instrument 

 

Startup procedure 

NOTE:

   If you have purchased accessories you may want to install these first before commencing 

with the Startup procedure. An overview of accessories is available on page 70, see also the 

specific documentation for the accessory.  

 

CAUTION 

Do not turn power to the instrument on and off quickly as this may 

damage the power supply. 

Wait at least 30 seconds before re-starting. 

1.

 

Open the sample compartment cover. 

2.

 

Make sure that the beam paths are free from obstruction. 
This means that no objects (for example, cables) project into the beam paths, no 

samples are in the sample compartment, and any accessories are properly installed. 

NOTE: 

  If the sample compartment is obstructed during the startup procedure, the spectrometer will 

not initialize correctly. 

3.

 

Close the sample compartment. 

4.

 

Switch on the power switch located at the top right hand corner of the instrument as 

shown in Figure 11. 
The switch will light up when there is power to the instrument. 

 

Figure 11 Power Switch 

5.

 

Switch on any accessories. 

6.

 

Wait until all instrument initialization is complete before starting the UV WinLab 

software.  
This will take approximately three minutes from switching the power on. 

NOTE:

   We recommend that for optimal performance of the instrument you should leave the 

spectrometer switched on for approximately one hour to allow the lamps to warm up and 

stabilize before starting analysis.  

Power switch 

Summary of Contents for Lambda 650









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands