manualshive.com logo in svg

PerkinElmer Lambda 650, Hardware Manual

Share
Download
PerkinElmer Lambda 650 Hardware Manual Download Page 13

Lambda 650/850/950 Hardware Guide . 13 

 

Precautions  

 

WARNING 

Be sure that all instrument operators read and understand the 

precautions listed below.  It is advisable to post a copy of the 

precautions near or on the instrument itself. 

The following precautions must be observed when using the Lambda 650/850/950: 

•

 

Connect the instrument to a correctly installed line power outlet that has a protective 
conductor (earth/ground). 

•

 

Do not attempt to make internal adjustments or replacements except as directed in this 
handbook. 

•

 

Do not operate the instrument with any covers or parts removed. 

•

 

Servicing should be carried out only by a PerkinElmer service representative or similarly 
authorized and trained person. 

•

 

Disconnect the instrument from all voltage sources before opening it for any 
adjustment, replacement, maintenance, or repair. If, afterwards, the opened instrument 

must be operated for further adjustment, maintenance, or repair, this must only be 

done by a skilled person who is aware of the hazard involved. 

•

 

Use only fuses with the required current rating and of the specified type for 
replacement. 

•

 

Do not use makeshift fuses or short-circuit the fuse holders. 
 

 

WARNING 

If the equipment is used in a manner not specified herein the protection 

provided by the equipment may be impaired. 

Summary of Contents for Lambda 650









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands