manualshive.com logo in svg

PerkinElmer Lambda 650, Hardware Manual

Share
Download
PerkinElmer Lambda 650 Hardware Manual Download Page 60

60 . Maintenance 

 

Replacing a Lamp 

If a lamp failure warning message is displayed, or you are seeing excessive noise on the 

baseline, you can replace the lamps as follows. 

 

 

WARNING 

Electrical Hazard 

High voltages are present at the lamp connectors in the lamp 

compartment – severe electric shock hazard. 

Never unplug or plug in a lamp cable while power is ON. 

Switch off the spectrometer and remove the plug from the electrical 

supply before starting with the replacement. 

 

High Temperatures - Risk of Burns 

Lamps soon become very hot, make sure that the lamps and the lamp 

compartment have cooled to room temperature before you touch them. 

 

UV Radiation 

The lamps emit intense UV radiation which can damage your eyes. 

Do not open the lamp compartment when the lamps are on. 

Do not gaze into a lighted lamp. 

The source lamps are located in the lamp compartment at the top left rear of the 

spectrometer, as shown in Figure 18. 

 

 

Figure 18 Lamp compartment 

Lamp compartment 

Summary of Contents for Lambda 650









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands