PerkinElmer Lambda 650 Hardware Manual Download Page 38

Page: 38 / 72

38 . Lambda 650 Installation

Connecting the System Components

WARNING

Electrical Hazard

To prevent potential injury to yourself and damage to the instrument,

switch

OFF

all instruments in the system and disconnect them from the

line power supply before you alter, or make any new electrical

connections.

•

The PC and the printer may be placed either side of the spectrometer, but must not be
placed on top of the spectrometer.
When placing instruments side by side, always leave a small gap between them.

•

Make sure that air can circulate freely over and under the system as well as behind it.

•

Do not place anything on or under any of the components that could hinder free air
circulation.

Connecting to the PC

The PC is connected using the connection marked COMPUTER on the right side of the

instrument, as shown in Figure 10.

Figure 10 PC Connection

NOTE:

We suggest that you place the ferrite choke supplied with the instrument around the lead.

NOTE:

You can use an external printer for hard-copy printouts of the analytical results. The printer

is connected via the PC.

To install the software, refer to the instructions that shipped with your software package.

PC connection

Summary of Contents for Lambda 650









































































Search results

Summary of Contents for Lambda 650

Reviews:

Brands by name

Popular brands

PerkinElmer Lambda 650, Hardware Manual

Search results

Summary of Contents for Lambda 650

Reviews:

Brands by name

Popular brands