manualshive.com logo in svg

PerkinElmer Lambda 650, Hardware Manual

Share
Download
PerkinElmer Lambda 650 Hardware Manual Download Page 67

Lambda 650/850/950 Hardware Guide . 67 

 

 

 

 

Figure 25 Four retaining screws in the sample compartment 

2.

 

Lift up the sample compartment off the locating pins and remove it from the 

spectrometer. 

Removing the Detector Unit 

 

 

WARNING 

Electrical Hazard 

The connector for the detector unit carries high voltage (130 V dc).  

Switch off and disconnect the instrument before removing or fitting a 

detector/accessory unit. 

1.

 

Switch off the spectrometer and disconnect the line power cord. 

2.

 

Open the sample compartment cover. 

3.

 

Undo the two retaining screws located under the blanking caps on the top of the 

detector (Figure 26) and are accessible using the long posidrive screwdriver supplied 

with the instrument. 

 

Figure 26 Undoing the retaining screws 

Retaining Screw 

Retaining Screw 

Retaining Screws 

Locating Hole 

Locating Slot 

Retaining screws under 
blanking caps 

Summary of Contents for Lambda 650









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands