Perkin-Elmer STA 6000 Installation And Hardware Manual Download Page 3

Page: 3 / 84

Contents

Introduction ............................................................................................... 5

Pyris Installation ............................................................................................... 6

Safety and Regulatory Information ........................................................... 7

Symbols Used in this Help .................................................................................. 8

Notes, Cautions and Warnings ..................................................................... 8

Symbols Used on the Instruments .....................................................................11

Electrical Warnings ...........................................................................................12

Electromagnetic Compatibility (EMC) .................................................................14

Europe ......................................................................................................14

South Korea ..............................................................................................14

United States (FCC) ...................................................................................14

Electrical Safety ...............................................................................................15

WEEE Instructions for PerkinElmer Products ......................................................16

Prepare the Laboratory ............................................................................ 19

Prepare the Laboratory .....................................................................................20

Electrical Requirements ..............................................................................20

Environmental Requirements ......................................................................20

Purge Gas and Pneumatic Supply ...............................................................21

Space Requirements ..................................................................................21

Install Multiple Analyzers ........................................................................ 23

Install Multiple Analyzers ..................................................................................24

Install an STA 6000 .................................................................................. 27

Safety Precautions for the STA 6000 .................................................................28

Important Specifications ............................................................................30

Decontamination and Cleaning ..........................................................................31

Decontamination .......................................................................................31

Cleaning the Instrument ............................................................................31

General Laboratory Safety ..........................................................................31

STA 6000 Warning Labels .................................................................................32

Warning Labels on the Upper Ring Around the Furnace................................32

Warning Labels on the Back of the STA 6000 ..............................................33

Installing an STA 6000 .....................................................................................35

Unpacking the STA 6000 ..................................................................................36

Parts Included ...........................................................................................37

Set Up the STA 6000 System Components .........................................................38

Select the Correct Voltage for the STA 6000 ................................................38

Connect the Purge Gas Supply to the STA 6000 ...........................................40

Connect the Purge Gas and System Purge Gas Lines to the STA 6000 ...........41

Remove the Shipping/Alignment Tool .........................................................42

Install the Sensor ......................................................................................42

Connect the Cooling Device to the STA 6000 ...............................................42

Connect the STA 6000 Components ..................................................................49

Configure the STA 6000 ....................................................................................50

Starting the Pyris Manager .........................................................................50

Calibrate the STA 6000 .....................................................................................51

STA 6000 Hardware ................................................................................. 55

STA 6000 Hardware Overview ...........................................................................56

Sample Handling ..............................................................................................58

Sample Preparation ...................................................................................58

Sample Pans .............................................................................................58

Sample Atmosphere ...................................................................................58

Loading the Sample into the STA 6000 .......................................................59

Summary of Contents for STA 6000





















































































Search results

Summary of Contents for STA 6000

Reviews:

Related manuals for STA 6000

Brands by name

Popular brands

Perkin-Elmer STA 6000, Installation And Hardware Manual

Search results

Summary of Contents for STA 6000

Reviews:

Related manuals for STA 6000

Brands by name

Popular brands