Perkin-Elmer STA 6000 Installation And Hardware Manual Download Page 37

Page: 37 / 84

Install an STA 6000 . 37

Parts Included

The STA 6000 comes in two boxes and consists of the following components:

•

STA 6000

•

Pyris software

•

Spares and Accessory Kit

The Spares and Accessories Kit contains the following parts:

Item

Part Number

Quantity

Sensor

N5202083

Indium Calibrating Reference Material

03190033

Silver Calibrating Reference Material

N5370438

Tweezers (pointed for sensor installation

and loading pans)

09908400

Tweezers (for sensor removal)

N5202093

Calibration Weight

N5200042

Alsiflex Paper (5 pieces)

N5376819

Ceramic Sample Pans (Pack of 3)

N5200040

Ceramic Sample Pans (Pack of 45) (with

autosampler instrument)

N5200045

Tubing Adaptor (1/8" to 1/4")

09903906

Gas Restrictor

01541498

Also included with the STA 6000 are:

•

Tygon tubing for connection of liquid coolant to the cooling chamber.

•

Hose clamps.

•

Teflon tubing for purge gas connection.

•

USB cable for communicating to the computer.

•

Power cord.

The procedure for unpacking the STA 6000 is complete.

Summary of Contents for STA 6000





















































































Search results

Summary of Contents for STA 6000

Reviews:

Related manuals for STA 6000

Brands by name

Popular brands

Perkin-Elmer STA 6000, Installation And Hardware Manual

Search results

Summary of Contents for STA 6000

Reviews:

Related manuals for STA 6000

Brands by name

Popular brands