Zwembad- en spaverwarmingsapparaat MASTERTEMP
™
P/N 475106 Rev. D 1/2016
28
| Hoofdstuk 3. Problemen oplossen
Apparaat ontbrandt niet - C
Start
Ga naar “PRIMAIRE
PROBLEEMOPLOSSING”
Observeer het apparaat gedurende
enkele minuten. Schakel het apparaat
enkele keren in en uit. Controleer op
de volgende zaken: ontsteking
vertraagt, slechte verbranding, te
vroeg doven van de vlam, tekenen
van koken of diagnose-led gaat
branden. Ga naar het specifeke
hoofdstuk probleemoplossing als
u een storing waarneemt.
Vervang de printplaat.
Vervang de gasklep door een
identiek exemplaar.
Herstel de bedrading tussen
aansluitingen TH en GND van de
regeleenheid van de
ontstekingsmodule en de printplaat.
Vervang de printplaat.
Herstel de bedrading tussen de
GAS-aansluitingen op de printplaat
en de gasklep.
OPMERKING 1:
spanning verschijnt
direct na warmtevraag en is mogelijk
gedurende slechts 30 seconden aanwezig.
OPMERKING 2:
spanning verschijnt ca.
24 seconden na warmtevraag en is mogelijk
gedurende slechts 7 seconden aanwezig.
Controleer of het hele traject van de
gastoevoer geopend is tot aan de
gasklep en of de gasklep geopend
is (stand ON).
Controleer of het hele traject van de
gastoevoer geopend is tot aan de
gasklep en of de gasklep geopend
is (stand ON).
Schakel de voeding naar het
apparaat gedurende 5
seconden uit en schakel de
voeding daarna weer in. Zorg
dat ingestelde
temperatuurwaarde hoger is
dan die van de
watertemperatuur. Wacht een
minuut.
Werd de brander ontstoken
en brandt deze nog?
Is de ventilator ingeschakeld?
Controleer of er gas naar de
brander stroomt tijdens de
ontstekingspogingen.
Observeer de gasmeter
tijdens de ontstekingspoging
(wacht ca. 30 seconden na
warmtevraag).
Controleer op 24 VAC
tussen aansluitingen TH en
GND op de regeleenheid
van de ontstekingsmodule.
ZIE OPMERKING 1.
Controleer op 24 VAC
tussen aansluitingen TH en
GND op de printplaat. ZIE
OPMERKING 1.
Controleer op 24 VAC
tussen de GAS-aansluitingen
op de printplaat. ZIE
OPMERKING 2.
Vervang de printplaat.
NEE
VERVOLG
JA
JA
JA
NEE
NEE
JA
NEE
JA
NEE
NEE
JA
JA
NEE
JA
JA
Brandt de led “SERVICE
HEATER”?
Ga naar “PROBLEMEN MET
BRANDER OPLOSSEN”
(pagina 32)
Ga naar “APPARAAT
ONTSTEEKT NIET - D” (pagina 31)
Controleer op 24 VAC tussen
aansluitingen VAL en GND op de
regeleenheid van de ontstekingsmodule.
ZIE OPMERKING 2.
Controleer op 24 VAC tussen
aansluitingen VAL en GND op de
printplaat. ZIE OPMERKING 2.
Als een van de rode diagnose-
leds (AGS, A
F
S, S
F
S, H
L
S,
PS of THERMISTOR) brandt,
ga dan naar pagina 30 en 31.
Is de brander ontstoken?
Vervang de regeleenheid van
de ontstekingsmodule.
NEE
JA
Herstel de bedrading tussen
aansluitingen VAL en GND van de
regeleenheid van de
ontstekingsmodule en de printplaat.
NEE
JA
NEE
NEE