![background image](http://html1.mh-extra.com/html/pentair/mastertemp-mt200hd/mastertemp-mt200hd_installation-and-user-manual_1525208017.webp)
P/N 475106 Rev. D 1/2016 MASTERTEMP
™
Pool and Spa Heater Installation and User’s Guide
|
9
PUMP
FILTER
POOL
HEATER
MANUAL
BY-PASS
TO
POOL
GATE
VALVE
FROM
POOL
PLUMBING CONNECTIONS
The MasterTemp™ heater has the capability of direct PVC
water piping plumbing connections. A set of bulkhead fittings
is included with the MasterTemp to insure conformity with
Pentair’s recommended PVC plumbing procedure. Other
plumbing connections can be used. See Figure 11 for plumbing
connections.
CAUTION
Before operating the heater on a new installation, turn on
the circulation pump and bleed all the air from the filter using
the air relief valve on top of the filter. Water should flow
freely through the heater. Do not operate the heater unless
water in the pool/spa is at the proper level. If a manual by-
pass is installed, temporarily close it to insure that all air is
purged from the heater.
VALVES
When any equipment is located below the surface of the pool or spa, valves should be placed in the circulation piping
system to isolate the equipment from the pool or spa. Check valves are recommended to prevent back-siphoning. Back-
siphoning is most likely to occur when the pump stops, creating a pressure-suction differential. Do NOT sanitize the pool
by putting chlorine tablets or sticks into the skimmer(s). When the pump is off, this will cause a high concentration of
chlorine to enter the heater, which could cause corrosion damage to the heat exchanger.
CAUTION
Exercise care when installing chemical feeders so as to not allow back siphoning of chemical into the heater, filters
or pump. When chemical feeders are installed in the circulation of the piping system, make sure the feeder outlet line
is down stream of the heater, and is equipped with a positive seal noncorrosive “Check Valve”, (P/N R172288),
between the feeder and heater.
MANUAL BY-PASS
( WATER FLOW RATE)
Where the water flow rate exceeds the maximum 454 L/m, a manual
bypass should be installed and adjusted. After installing the valve, adjust
the valve to bring the flow rate within the acceptable range. Then remove
the valve handle or lock it in place to avoid tampering. See
Figure 11
.
Figure 10.
Table 1.
Cool water in
Warm water out
Outlet to pool
Inlet to heater
1. Set Manual By-Pass Valve.
2. Remove Handle.
See page 33 for Pressure Relief Valve Installations.
Figure 11.
l
e
d
o
M
)
M
P
G
(
m
/
L
.
n
i
M
*
)
M
P
G
(
m
/
L
.
x
a
M
0
0
2
)
0
2
(
6
7
)
0
2
1
(
4
5
4
0
0
3
)
0
3
(
4
1
1
)
0
2
1
(
4
5
4
0
0
4
)
0
4
(
2
5
1
)
0
2
1
(
4
5
4
d
e
d
n
e
m
m
o
c
e
r
m
u
m
i
x
a
m
e
h
t
d
e
e
c
x
e
t
o
n
o
D
*
.
g
n
i
p
i
p
g
n
i
t
c
e
n
n
o
c
e
h
t
r
o
f
e
t
a
r
w
o
l
f
Section 2. Installation