manualshive.com logo in svg

Pentair Hydromatic NOVUS 3000 Series, Installation And Service Manual, Page: 9 / 12

Share
Download
Pentair Hydromatic NOVUS 3000 Series Installation And Service Manual Download Page 9

9

  3. Capacitor check.
  a. Make sure the ca pac i tor is 

dis 

charged. Use extreme 

caution as a spark might 

occur.

  b.  Disconnect  the  ca pac i tor 

leads and connect an analog-

type volt-ohmmeter to the 

capacitor terminals.

  c. Set the meter on the 

RX1,000 scale to check the 

start ca pac i tor. Set the meter 

on the RX10,000 scale to 

check  the  run  ca pac i tor.

 d. 

The meter should 

 

in di cate low ohms when it 

is first connected, but as 

the  ca pac i tor  becomes 

charged (by the meter), it 

will return to a read ing of  

infinity (open circuit).

  4. Start relay check.
  a. Check the coil re sis tance It 

should be 3,000 to 15,000 

ohms.

  b. Install a clamp on amp 

meter around the start 

 

wind ing  lead.

  c. Set the amp meter scale to 

at least 2 times the pump 

motor full load current.

  d. Place the H-O-A switch in 

the Hand position to start 

the pump.

  e. The meter should read 

ap prox i mate ly  2  times  full 

load current during starting. 

  f. After the motor has started 

(within one sec 

ond) the 

 

cur rent should drop to a 

value much less than full 

load  cur rent.

  5. Motor voltage check:

 Typical 

 

Motor   Voltage 

Component  Lead  Mode Reading

Main Winding 

Black to 

Start 

Line Voltage 

 White

Main Winding 

Black to 

Run 

Line Voltage 

 White

Start Winding 

Black to 

Start 

Line Voltage 

 Red

Start Winding 

Black to 

Run 

120% 

 

Red 

 

Line Voltage

Duplex Pump Controller

AUX RELAY

/ HORN  

ALT

ALTERNATION

HIGH

ALARM

LOW

ALARM

HIGH

FLOAT

LAG

FLOAT

LEAD

FLOAT

OFF

FLOAT

LOW

FLOAT

MUTE

DISABLED

PUMP 1

PUMP 2

PUMP 1

PUMP 2

PUMP 1

PUMP 2

FLOATS OUT OF ORDER

TEMP FAIL

SEAL FAIL

RESET

PUMP 2

PUMP 1

1 - 2

2 - 1

Summary of Contents for Hydromatic NOVUS 3000 Series













Reviews:

No comments