background image

 

13 |

 

S t r o n a

 

 

3.

 

INSTALLATION 

 

 

3.1. Chimney 

 

The   parameters   of    chimney   should   be   adjusted   to    requirements    of   heating   device,   of 
which  fumes  are  led  away  to chimney.  The chimney can  be  made of ceramics  or   steel. 
Chimney  should  be  clean,  and  its  draft  sufficient  for  Pellas X  burner  operating  with heating  
device  in  scope  of  preset  power  output.  In  case  when  chimney  draft  is  not sufficient, it is  
possible to install a  mechanical fumes exhaust.  Before operation chimney should be checked and 
approved by a qualified chimney-sweeper. 

 

It  should  be  remembered  that  a  high  chimney  with  big  capacity  of  fumes  needs  more 
heat and temperature of inner part of it should not be lower than 80ºC, 1m below the top to avoid 
condensation  on top of the chimney. To  reduce  the inner profile of the chimney, a  steel pipe with 
proper  diameter can  be installed.  All advice  referring to  chimney  duct should be taken from  
a  professional company. Strong wind, too  high or too low  chimney have  influence  on  efficiency  
of  burner  and  its  settings.  In  such  cases  it  is  advised  to install a  stabilizer of chimney  
draft which  will ventilate chimney and help  in maintaining stable draft. If chimney is too small,  
then  burner    may  not  work  correctly,  in  such  case  it  is  necessary  to  install  a  mechanical  fumes 
exhaust. 

Table 4. Minimum chimney draft. 

TYPE OF BURNER 

MINIMUM CHIMNEY DRAFT [Pa] 

HYBRID Mini 

15 

HYBRID Mini 35 

15 

HYBRID 44 

20 

 

 

3.2. Boiler / oven 

 

Pellas X burner can be installed in majority of boilers. The power of  burner in relation to boiler or 
oven power  must  be  adjusted  by  installer.  It  is  the best  to mount  the  burner in  boiler’s 
door,  just above grate  or  in  side  wall if it is possible. The diameters of mounting holes of Pellas 
X burner are given in table 3. The length of pipe in boiler is regulated by installer with usage of a 
connector – mounting flange – similar as in oil  boilers  or  directly  into  door  of  boiler  with  4  
M8  screws. Thanks  to  connector  it  is possible to  regulate  length  of  furnace  pipe  of  burner  
in  boiler.  If  boiler  chamber is too small, burner may operate incorrectly. 

Summary of Contents for HYBRID 44








































Reviews: