PDi PDI-P26LCDC Installation And Operating Instructions Manual Download

Page: 21 / 52

PDI-P26, 32, 40 TV Installation Guide

Page 21 of 52

Communication Systems Inc.

Better Solutions Are Within Reach™

INSTALLATION and OPERATING INSTRUCTIONS

PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH +1-937-743-6010 PH +1-937-743-5664

Document Number: PD196I127R1.DOC

Minimum Volume

Sets the minimum volume level the TV can reach. Setting this to any value other than 0 guarantees that some level of
sound will always be heard when the TV is operating.

Enter the Sound menu.

Press

▲

▼

to highlight Minimum Volume.

Press

◄

►

to select the desired number (0-100).

Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear.

Maximum Volume

Sets the maximum volume level the TV is allowed to reach.

Enter the Sound menu

Press

▲

▼

to highlight Maximum Volume.

Press

◄

►

to select the desired number (0-100).

Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear.

Power on Volume

Sets the initial volume for when the TV is turned on.

NOTE:

If Power on Volume is set to Last and the physical power is removed, the TV will power on with a

volume of 0.

Enter the Sound menu

Press

▲

▼

to highlight Power on Volume.

Press

◄

►

to select the desired number (0-100) or Last.

NOTE:

Last will cause the TV to be at the last volume setting before it was turned off.

Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear.

Summary of Contents for PDI-P26LCDC





















































Search results

Summary of Contents for PDI-P26LCDC

Reviews:

Related manuals for PDI-P26LCDC

Brands by name

Popular brands

PDi PDI-P26LCDC, Installation And Operating Instructions Manual

Search results

Summary of Contents for PDI-P26LCDC

Reviews:

Related manuals for PDI-P26LCDC

Brands by name

Popular brands