Partner RP-330 Technical Manual Download Page 42

Page: 42 / 81

RP-330 Technical Manual

ESC S

[Name]

Select standard mode

[Format]

ASCII

ESC

Hex

Decimal 27

[Description]

Switches from page mode to standard mode.

[Details]

·This command is effective only in page mode.

·Data buffered in page mode and the printable area developed in page mode are cleared.
·This command is switches the setting for the following command (in which the values can be set

independently in standard mode and page mode) to those for standard mode:

①

Set right-side character spacing:

ESC SP, FS S

②

Select default line spacing :

ESC 2, ESC 3

·The following commands are enabled only to set in standard mode.

①

Set printing area in page mode :

ESC W

②

Set print direction in page mode :

ESC T

·The following commands are ignored in standard mode.

①

Set absolute vertical print position in page mode :

GS $

②

Set relative vertical print position in page mode :

＼

·Standard mode is selected automatically when power is turned on, the

printer is reset, or command

ESC @

is used.

[Reference]

FF, ESC FF, ESC L

Summary of Contents for RP-330


















































































Search results

Summary of Contents for RP-330

Reviews:

Related manuals for RP-330

Brands by name

Popular brands

Partner RP-330, Technical Manual

Search results

Summary of Contents for RP-330

Reviews:

Related manuals for RP-330

Brands by name

Popular brands