Partner RP-330 Technical Manual Download Page 36

Page: 36 / 81

RP-330 Technical Manual

commands (

DLE EOT, DLE ENQ, DLE DC4

) until it is enabled by this command.

[Default] n=1

ESC ? n

[Name]

Cancel user-defined characters

[Format]

ASCII

ESC

Hex

Decimal 27

[Range]

32 ≤

≤126

[Description]

Cancels user-defined characters.

[Details]

·This command cancels the pattern defined for the character code

specified by n. After the user-defined characters is canceled, the corresponding pattern for the
internal character is printed.

·This command deletes the pattern defined for the specified code in the

font selected by

ESC

·If a user-defined character has not been defined for the specified

character code, the printer ignores this command.

[Reference]

ESC &

ESC %

ESC @

[Name]

Initialize printer

[Format]

ASCII

ESC

Hex

Decimal 27

[Description]

Clears the data in the print buffer and resets the printer mode to the mode

that was in effect when the power was turned on.

[Details]

·The DIP switch settings are not checked again.

·The data in the receive buffer is not cleared.
·The macro definition is not cleared.
·The NV bit image data is not cleared.
·The data of the NV user memory is not cleared.

Summary of Contents for RP-330


















































































Search results

Summary of Contents for RP-330

Reviews:

Brands by name

Popular brands

Partner RP-330, Technical Manual

Search results

Summary of Contents for RP-330

Reviews:

Brands by name

Popular brands