Parker Torqmotor TF Series Service Procedure Download Page 8 | Manualshive

Page: 8 / 44

background image

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

8

•  Clean, petroleum-based solvent
•  Emery paper
•  Vise with soft jaws
•  Air pressure source
•  Arbor press
•  Screw driver
•  Masking tape
•  Breaker bar
•  Torque wrench-ft. lbs. (N m)
•  Sockets: 1/2 or 9/16 inch thin wall, 1 inch
•  Allen Sockets: 3/16, 3/8 inch
•  Adjustable crescent wrench or hose fitting wrenches
•  SAE 10W40 SE or SF oil
•  Special bearing mandrel for TH Torqmotors (consult factory)
•  Special bearing mandrel for TF, TG & TJ Torqmotors (SEE FIGURE 1)
•  Feeler gage .005 inch (.13 mm)
•  TH Torqmotors require blind hole bearing puller for a 1.575 inch dia. (40.0 mm) and 2.130 inch dia. (54.1 mm)

bearings.

• TF, TG & TL Torqmotors require blind hole bearing puller for 1.400 inch dia. (35.6 mm) and 2.130 inch dia. (54.1

mm) bearings.

• Clean corrosion resistant grease. Part #406018 is included in each seal kit. Recommended grease is Parker

Specification #045236 or Mobil Mobilith SHC

®

460

NOTE: The available service seal kits include the recommended grease as a grease pack #406018

CAUTION: Mixing greases that have different bases can be detrimental to bearing life.

Tools and Materials Required for Servicing

«
...
6
7
8
9
10
...
»

Summary of Contents for Torqmotor TF Series













































Reviews:

No comments

Related manuals for Torqmotor TF Series

Brand: hager Pages: 4

Brand: Kubota Pages: 285

Brand: Man Pages: 132

Brand: Beckhoff Pages: 31

Brand: Selve Pages: 24

Brand: Yamaha Pages: 51

Brand: FPT Pages: 49

Brand: HIOTH TECHNOLOGY Pages: 5

Brand: Rockwell Automation Pages: 28

Brand: Stiga Pages: 168

Brand: Team Biland Pages: 18

SENSORLESS-BLDC-MOTOR-RD

Brand: Silicon Laboratories Pages: 12

Brand: JAC Pages: 801

Brand: YARDMAX Pages: 25

Parilla x30 125cc RL-TaG

Brand: IAME Pages: 47

Brand: Mitsubishi Pages: 106

Brand: Nakanishi Pages: 2

Brand: Nakanishi Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands