Parker Torqmotor TF Series Service Procedure Download Page 41

Page: 41 / 44

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

Tips for Maintaining the Torqmotor™ Hydraulic System

• Adjust fluid level in reservoir as necessary.

• Encourage all operators to report any malfunction or accident that may have damaged the hydraulic system

or component.

• Do not attempt to weld any broken Torqmotor™ component. Replace the component with original equipment

only.

• Do not cold straighten, hot straighten, or bend any Torqmotor™ part.

• Prevent dirt or other foreign matter from entering the hydraulic system. Clean the area around and the filler

caps before checking oil level.

• Investigate and correct any external leak in the hydraulic system, no matter how minor the leak.

• Comply with manufacturer’s specifications for cleaning or replacing the filter.

CAUTION: Do not weld, braze, solder or any way alter any Torqmotor™ component.

CAUTION: Maximum operating pressure must not exceed recommended Torqmotor™ pressure

capacity.

CAUTION: Always carefully inspect any system component that may have been struck or damaged

during operation or in an accident. Replace any component that is damaged or that is questionable.

CAUTION: Do not force any coupling onto the Torqmotor™ coupling shaft as this could damage the unit

internally.

Parker extends close technical cooperation and assistance. If problems occur which you cannot solve, please

contact your local Parker approved Distributor or Parker Technical Support. Our phone number and fax
number and address are on the back cover of this manual.

Tips

Summary of Contents for Torqmotor TF Series













































Search results

Summary of Contents for Torqmotor TF Series

Reviews:

Related manuals for Torqmotor TF Series

Brands by name

Popular brands

Parker Torqmotor TF Series, Service Procedure

Search results

Summary of Contents for Torqmotor TF Series

Reviews:

Related manuals for Torqmotor TF Series

Brands by name

Popular brands