Parker Torqmotor TF Series Service Procedure Download Page 5 | Manualshive

Page: 5 / 44

background image

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

5

Introduction

This service manual has one purpose: to guide you
in maintaining, troubleshooting, and servicing the TF,
TG, TH and TL Torqmotor™ (low-speed, high-torque
hydraulic motor).
Material in this manual is organized so you can work
on the Torqmotor™ and get results without wast-
ing time or being confused. To get these results, you
should read this entire manual before you begin any
work on the Torqmotor™.
This manual also contains troubleshooting information
and checklist. If you must service the Torqmotor™,
the checklist will help you to determine where the
problem may be.
The three-column format of the Disassembly and
Inspection, and Assembly sections will make it easier
for you to conduct major work on the Torqmotor™.
Column 1 gives a brief key for each procedure. Col-
umn 2 explains in detail the procedure you should
follow. Column 3 illustrates this procedure with pho-
tographs. Read all material carefully and pay special
attention to the notes, cautions, and warnings.

A page with the Torqmotor™ exploded assembly view
is provided several places in this manual. The compo-
nent part names and item numbers assigned on this
exploded assembly view correspond with names and
item numbers (in parentheses) used in the disassem-
bly and assembly procedures set forth in this manual.
Service part list charts are also provided in this
manual with the part names and exploded view item
numbers cross referenced to Parker service part
numbers.
Service parts are available through the Original Equip-
ment Manufacturer or Parker approved TF, TG, TH
and TL Torqmotor™ Distributors.
As you gain experience in servicing the Torqmotor™,
you may find that some information in this manual
could be clearer or more complete. If so, let us know
about it. Do not try to second guess the manual. If
you are stuck, contact us. Servicing the Torqmotor™
should be a safe and productive procedure, in order
for the unit to deliver the reliable, long-life operation
engineered into it.

«
...
3
4
5
6
7
...
»

Summary of Contents for Torqmotor TF Series













































Reviews:

No comments

Related manuals for Torqmotor TF Series

CentriPro Xtreme Duty Series

Brand: Xylem Pages: 12

Brand: Saito Pages: 8

T-MODE TM 45 R 15/17

Brand: FAAC Pages: 10

Brand: Erreka Pages: 30

LYCOMING 200-6XL Series

Brand: E-MAG Pages: 30

MaxxForce DT 10

Brand: Navistar Pages: 109

Brand: Bartec Varnost Pages: 48

EM-PMI540-T1500

Brand: Danfoss Pages: 76

Brand: Volvo Pages: 179

Brand: Honda Pages: 139

Brand: Honda Pages: 64

Brand: Honda Pages: 84

Brand: Volvo Pages: 11

Brand: Volvo Pages: 36

Brand: Volvo Pages: 48

Brand: Volvo Pages: 64

Brand: Detroit Diesel Pages: 135

Brand: Honda Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands