Parker Torqmotor TF Series Service Procedure Download Page 19

Page: 19 / 44

HY13-1527-M1/US

Torqmotor™ Service Procedure

TF, TG, TH and TL Series

Parker Hannifin Corporation

Hydraulic Pump/Motor Division

Greeneville, TN 37745 US

Preparation Before Disassembly

• Before you disassemble the Torqmotor™ unit or any of its components read this entire manual. It provides

important information on parts and procedures you will need to know to service the Torqmotor™.

• Determine the type of end construction from the alternate views shown on the exploded view.

• The Series TF, TG, TL & TH Torqmotors™ will have a 5 inch (127.9 mm) main body outside diameter and seven

3/8 24 UNF 2A cover bolts.

• Refer to “Tools and Materials Required for Services” section for tools and other items required to service the

Torqmotor™ and have them available.

• Thoroughly clean off all outside dirt, especially from around fittings and hose connections, before disconnect-

ing and removing the Torqmotor™. Remove rust or corrosion from coupling shaft.

• Remove coupling shaft connections and hose fittings and immediately plug port holes and fluid lines.

• Remove the Torqmotor™ from system, drain it of fluid and take it to a clean work surface.

• Clean and dry the Torqmotor™ before you start to disassemble the unit.

• As you disassemble the Torqmotor™ clean all parts, except seals, in clean petroleum-based solvent, and blow

them dry.

WARNING: petroleum-base solvents are flammable. Be extremely careful when using any solvent. Even a small
explosion or fire could cause injury or death.

WARNING: WEAR EYE PROTECTION AND BE SURE TO COMPLY WITH OSHA OR OTHER MAXIMUM AIR
PRESSURE REQUIREMENTS.

CAUTION: Never steam or high pressure wash hydraulic components. Do not force or abuse closely fitted parts.

• Keep parts separate to avoid nicks and burrs.

• Discard all seals and seal rings as they are removed from the Torqmotor™. Replace all seals, seal rings and

any damaged or worn parts with genuine Parker or OEM approved service parts.

Disassembly and Inspection

Summary of Contents for Torqmotor TF Series













































Search results

Summary of Contents for Torqmotor TF Series

Reviews:

Related manuals for Torqmotor TF Series

Brands by name

Popular brands

Parker Torqmotor TF Series, Service Procedure

Search results

Summary of Contents for Torqmotor TF Series

Reviews:

Related manuals for Torqmotor TF Series

Brands by name

Popular brands