Parker PSD1 Installation Instructions Manual Download Page 48

Page: 48 / 109

Installation of the multi-axis system PSD1-M

48 (109)

192-011006N8 2019-07

09.10.19 09:27

Status

No.

Status of axis

Left LED a

(green) (ready)

Right LED b

(red) (error)

Axis in error state / error

present / axis energized (error
reaction 1)

flashes quickly (5 HZ)

Axis in error state / error
present / axis de-energized
(error reaction 2)

off

Axis faulty: Please contact us

STO active

off

flashes slowly (1 HZ)

reserved

flashes quickly

flashes quickly (5 HZ)

SD Card detected or
restoring from SD card
successfully terminated

alternate quick flashing

(LEDa green, LEDb green)

SD card not detected or
restoring from SD card
interrupted

alternate quick flashing

(LEDa red, LEDb red)

Axis de-energized

off

Single flash

Axis energized

Single flash

Axis de-energized
HEDA3 slave not ready

off

Double flash

Axis energized
HEDA3 Slave not ready

Double flash

Axis de-energized
HEDA3 Master not ready

off

Triple flash

Axis energized
HEDA3 Master not ready

Triple flash

Axis de-energized

off

Jitter (10 HZ)

Axis energized

Jitter (10 HZ)

Error response 1: Ramping with slow ramp; then deactivate control loops.
Error response 2: Ramping with "Stop" ramp, then deactivate control loops.
For the meaning of individuals errors please go to Error list.

Single flash

Double flash

Triple flash

Caution - Risk of electric shock!

High voltage supply may be present even with missing voltage supply (both

LEDs off)!

Summary of Contents for PSD1














































































































Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands

Parker PSD1, Installation Instructions Manual

Search results

Summary of Contents for PSD1

Reviews:

Related manuals for PSD1

Brands by name

Popular brands