background image

Introduction 

 

 

 

 

12  (109)

 

192-011006N8 2019-07 

09.10.19 09:27 

 

 Check that all live terminals are secured against contact. Dangerous voltages up 

to 850V occur. 

 Do not short-circuit the DC power voltage. 

  

CAUTION: Risk of electric shock 

 

 

 

 

Caution - Risk of electric shock! 

Before wiring or loosening electrical connections please observe the 

following:

 

 Risk of electric shock, disconnect power before removing cover resp. 

disconnect the devices from the mains supply. 

 

Caution!

 Dangerous electrical voltage even after turning off the intermediate 

capacitors: 

Up to 

3 minutes with PSD1-S and 10 minutes with PSD1-M 

after switching off 

mains supply, dangerous voltages may still be present.

 

Please check that no voltages are present (<50 V) at the output terminals DC+ 

and DC- of PSD1-S: X63/3 & X63/5 and with PSD1-M: Bus HV DC - 3 & 5. rail. 

 

 

 The device must be permanently grounded due to high earth leakage currents. 

The leakage current is greater than 3.5 mA. 

 The drive motor must be grounded with a suitable protective lead. 

 

 

 

 The devices are equipped with high voltage DC capacitor. Before removing the 

protective cover, the discharging time must be awaited. After switching off the 

supply voltage, it may take up to 3 minutes with PSD1-S and 10 minutes with 

PSD1-M (up to 30 minutes with additional capacitor modules) to discharge the 

capacitors.   

Danger of electric shock in case of non respect. 

 

 Do never perform resistance tests with elevated voltages (over 690V) on the 

wiring without separating the circuit to be tested from the drive. 

 Please exchange devices only in currentless state and, in an axis system, only in 

a defined original state. 

 If the axis controller is replaced, it is absolutely necessary to transfer the 

configuration determining the correct operation of the drive to the device before 

the device is put into operation. Depending on the operation mode, a machine 

zero run will be necessary. 

 The device contains electrostatically sensitive components. Please observe the 

electrostatic protection measures while working at/with the device as well as 

during installation and maintenance.   

 

2.8.5. 

Cautionary Markings 

 

 

Ignoring of the following instructions will result in personal injury or material 

damage. 

 

 The heat disispator can reach very high temperatures (>70°C) 

 Do never perform resistance tests with elevated voltages (over 690V) on the 

wiring without separating the circuit to be tested from the drive. 

 Please exchange devices only in currentless state and, in an axis system, only in 

a defined original state. 

 

 If the axis controller is replaced, it is absolutely necessary to transfer the 

configuration determining the correct operation of the drive to the device before 

the device is put into operation. Depending on the operation mode, a machine 

zero run will be necessary. 

 

 The device contains electrostatically sensitive components. Please heed the 

electrostatic protection measures while working at/with the device as well as 

during installation and maintenance.   

 Never carry out high voltage resistance tests at lines without disconnecting the 

drive from the power supply you need to check. 

 

Summary of Contents for PSD1-SW1200














































































































Reviews: