background image

F.  How to Assemble Your Handset 

  14                                      Questions about eRapid?   Call 1-866-335-6943 

 

 

 

Step F5.

 

Insert the Aerosol Head

 making sure that it is 

labeled “eRapid” (

Figure F5a

, detail).  

Do Not use 

other Aerosol Heads in this device.  

Being 

careful to touch 

ONLY

 the plastic outer ring of the 

Aerosol Head, squeeze the 2 flexible plastic arms 

on the side of the Aerosol Head (

Figure F5b

together while firmly inserting 2 plastic tabs and 2 

metal prongs into the 4 holes of the Medication 

Reservoir.  You should feel the plastic tabs “grab” 

as you insert it. It is important that you 

Do Not 

touch the metal part of the Aerosol Head 

(

Figure 

F5c

).

 

 
 
 
 
 
 
 
 
 
 
 

Step F6.

 

Close the Handset

 by pushing the Aerosol 

Chamber together with the Medication Reservoir 

until you hear or feel a “snap” (

Figure F6

).  If you 

Do Not

 hear or feel a “snap”, open the Handset 

and check that the Blue Valve is seated properly.

 

 

 
 
 
 

Step F7.

 

Attach Mouthpiece to Handset. 

 Make sure the 

Blue Flap is facing up (

Figure F7

) and is pressed in 

the slot on the Mouthpiece.  Push the Mouthpiece 

straight onto the Handset.  Make sure the 

Mouthpiece stays attached to the Handset during 

treatment.

 

 

 

IMPORTANT

:

  Do Not touch the metal part of the 

Aerosol Head. 

Arms 

Medication Reservoir with 4 Holes 

Aerosol Head Detail 

F5a

 

F5b

 

F5c

 

F6

 

F7

 

e

Rapid

 

Blue Flap 

Summary of Contents for eRapid

























Reviews: