background image

E.  How To Clean and Maintain Your eRapid 

  10                                      Questions about eRapid?   Call 1-866-335-6943 

 

Disinfecting Your Handset 

 

To reduce the risk of serious or fatal illness or injury caused by 

contamination, it is important to disinfect your Handset daily or as 

recommended by your physician.  Disinfection is more effective if 

you clean your Handset before you disinfect. 

 

Step E9:

 

Disinfect the Handset 

with the commercially 

available medical device disinfectant Control III® or 

by boiling in distilled water.

 

 

 

To disinfect with disinfectant

, mix ½ 

tablespoon of Control III solution to 1 quart of 

water in a clean bowl.  Immerse the parts in that 

bowl and soak for 

10 minutes

 (

Figure E9a

).  

Remove parts from solution and rinse thoroughly 

with sterile water. 

 

 

To disinfect with boiling water

, immerse and 

boil the parts, including the Aerosol Head, in a 

clean pot of 

distilled

 water for a full 5 minutes 

(

Figure E9b

). 

 
 

Step E10:

 

Dry on a lint-free cloth or paper towel (Figure 

E10)

.  After the parts are completely dry, place 

them in a bag or cover them with a lint-free cloth or 

paper towel for storage. Re-assemble the Handset 

just prior to the next treatment.   

 

Unclogging the Aerosol Head with Easycare 

(Optional) 

 

After multiple uses, your nebulization time may slowly increase.  If 

soaking in soapy water does not improve performance, it may be 

necessary to perform special cleaning of the Aerosol Head.  The 

Easycare

 is used to clean and unclog the small holes in the 

Aerosol Head by reversing the flow of liquid.  The cleaning process 

takes about 5-10 minutes and uses the 

Easycare

 powered by the 

Controller. 

 It is important NOT TO USE 

the 

Easycare

 more than 

30 times on a single Aerosol Head. 

Clean the Handset as described in Steps E1-E7.  

Step E11:

 

Open the Easycare.  

 

Press lightly on the side gripping surfaces to release 

the side engaging hooks

 (Figure E11)

.    

 

Gently pull the light gray funnel part outward and 

down. 

 

E11

 

E9a

 

E9b

 

E10

 

Summary of Contents for eRapid

























Reviews: