ParaBody Parabody 660 User Manual Download Page 31 | Manualshive

Page: 31 / 51

background image

31

FIGURE 33

STEP 33

0

1

2

3

4

5

6

1/2

1/2

1/2

1/2

1/2

1/2

•

SECURELY

assemble one 1/2” SPRING PIN ASSEMBLY (52) to the spring pin housing on the PRESS SUPPORT TUBE (21).

(NOTE: Tighten the nut of the SPRING PIN ASSEMBLY SECURELY.)

•

SECURELY

assemble the BACK PAD (39) to the PRESS BACK SUPPORT (23) using two 3/8 X 2-3/4” BOLTS (85) and two 3/8”

WASHERS (91). See FIGURE 33.

85 3/8 X 2-3/4”

95 LOW
HEIGHT

52

23

91

39

21

95 LOW
HEIGHT

10

1/2 X 4-1/2” 89

1/2 X 3” 87

•

SECURELY

assemble the PRESS BACK SUPPORT (23) to the PRESS SUPPORT TUBE (21) using one 1/2” X 3” BOLT (87)

and one 1/2” LOW HEIGHT LOCK NUT (95).

(NOTE: Tighten the connection enough to remove play, yet allowing the

PRESS BACK SUPPORT to rotate freely).

•

SECURELY

assemble the PRESS SUPPORT TUBE (21) to the PRESS SWIVEL (10) using one 1/2” X 4-1/2” BOLT (89) and

one 1/2” LOW HEIGHT LOCK NUT (95).

(NOTE: Tighten the connection enough to remove play, yet allowing the PRESS

SUPPORT TUBE to rotate freely).

«
...
29
30
31
32
33
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: Hammer Strength Pages: 8

Brand: Sharper Image Pages: 3

Studio Preacher Curl

Brand: Taurus Pages: 28

Brand: Taurus Pages: 28

Brand: Taurus Pages: 68

Brand: Hoist Fitness Pages: 79

Brand: MBH Fitness Pages: 12

Powerhouse Elite PHE 9000

Brand: Impex Pages: 29

MARCY MWB-70500

Brand: Impex Pages: 11

Brand: Impex Pages: 11

Brand: Gorilla Gym Pages: 20

Csb32 Slant Board

Brand: Weider Pages: 6

Clubstepper SM10

Brand: Weider Pages: 16

Brand: Weider Pages: 16

Brand: Weider Pages: 31

Brand: Kettler Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands