ParaBody Parabody 660 User Manual Download | Manualshive

Page: 26 / 51

background image

26

STEP 26

•

SECURELY

assemble one 3/8” X 1” BUTTON HEAD CAP SCREW (96) and one 3/8” LOCK NUT (92) to the last hole on the BACK

PAD ADJUST (16). See FIGURE 27.

FIGURE 27

•

SECURELY

insert one 2” SQ. END CAP (46) to the open end of the BACK PAD ADJUST (16). See FIGURE 27.

• SECURELY tighten all loose frame connections made to this point.

(!!! IMPORTANT !!! to assure proper function of the 425,

the loose frame connections must be tightened in the following order)

Tighten the:

• MIDDLE UPRIGHT (8) to the BASE (1) and to the TOP BOOM (17).
• REAR UPRIGHT (4) to the BASE (1) and to the TOP BOOM (17).
•

PRESS BASE (18) to the REAR (4) and MIDDLE UPRIGHTS (8).

• PRESS BASE (18) to the BASE (1).
• FRONT UPRIGHT (25) to the BASE (1).

NOTE: DO NOT TIGHTEN THE FRONT UPRIGHT TO THE TOP BOOM AT THIS TIME.

92

46

96

8

25

4

1

17

18

BUTTON

HEAD

«
...
24
25
26
27
28
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: TOORX Pages: 25

Brand: Hammer Strength Pages: 13

Brand: Body Solid Pages: 4

Brand: MegaTec Pages: 26

Studio Preacher Curl

Brand: Taurus Pages: 28

Brand: Taurus Pages: 28

Brand: Hoist Fitness Pages: 79

Brand: Stamina Pages: 18

100328-00049-0001

Brand: gorilla sports Pages: 16

Brand: INTERSPORT Pages: 69

Brand: Powerline Pages: 3

Brand: Kettler Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands