ParaBody Parabody 660 User Manual Download | Manualshive

Page: 17 / 51

background image

17

STEP 15

•

LOOSELY

assemble the TOP BOOM (17) to the top of the REAR UPRIGHT (4) using two 1/2 X 4” BOLTS (88) two 1/2” WASHERS (93)

and one 1/2” LOCK NUT (94). See FIGURE 15.

FIGURE 15

•

SECURELY

assemble one 3/8” SPRING PIN ASSEMBLY (51) to the SPRING PIN HOUSING on the FRONT UPRIGHT (25) as shown in

FIGURE 15.

• Assemble one 3-PRONG KNOB (61) to the FRONT UPRIGHT (25) as shown in FIGURE 15.

• Assemble two ROLLER PADS (37) to the FRONT UPRIGHT (25) using one 3/4 OD X 16” TUBE (35) and two STARLOCK

COLLARS (50). See FIGURE 15.

37

17

50

51

1/2 X 4” 88

93

94

35

61

25

37

50

4

0

1

2

3

4

5

6

1/2

1/2

1/2

1/2

1/2

1/2

«
...
15
16
17
18
19
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: Impex Pages: 11

Brand: ProForm Pages: 39

Brand: York Fitness Pages: 40

Brand: First Degree Pages: 20

Brand: First Degree Pages: 23

Brand: StrengthTrainer Pages: 24

Brand: Impex Pages: 13

Iron Grip Strength IGS-412

Brand: Impex Pages: 10

Iron Grip Sport IGS-05

Brand: Impex Pages: 11

Brand: Impex Pages: 14

COMPETITOR WM-343

Brand: Impex Pages: 11

Brand: Impex Pages: 14

Brand: Body Solid Pages: 30

Brand: FLOWFITNESS Pages: 57

Brand: habitat et jardin Pages: 33

Adjustable Bench 30FB

Brand: Life Fitness Pages: 1

Brand: Life Fitness Pages: 9

Club Series 45X

Brand: Life Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands