ParaBody Parabody 660 User Manual Download Page 20 | Manualshive

Page: 20 / 51

background image

20

FIGURE 19

STEP 19

•

SECURELY

assemble

one 3/8” SPRING PIN (51) to the ROLLER PAD ADJUST (11) as shown in FIGURE 19.

• Insert two 1/2” FLANGE BEARINGS (78) into the LEG CURL/EXT (15) as shown on FIGURE 19.

•

Slide ROLLER PAD ADJUST (11) over the LEG CURL/EXT (15) until the spring pin pops into the holes. See FIGURE 19.

•

SECURELY

assemble one 3/8 X 1” BUTTON HEAD CAP SCREW (96) and one 3/8” LOCK NUT (92) to the last hole in the LEG

CURL/EXT (15) as shown in FIGURE 19.

•

Insert one 2” SQ. END CAP (46) into the end of the LEG CURL/EXT (15) as shown in FIGURE 19.

• Assemble two ROLLER PADS (37) to the ROLLER PAD ADJUST (11) using two STARLOCK COLLARS (50).

• Assemble the LEG CURL/EXT (15) to the FRONT UPRIGHT (25) using one 1/2 X 3” BOLT (87), two BOLT COVER CAPS (110), two

BOLT COVER WASHERS (111), and one 1/2” LOW HEIGHT NUT (95).

(NOTE: Tighten the connection enough to remove play, yet

allowing the LEG CURL/EXT to rotate freely.)

96 3/8 X 1”

87 1/2 X 3”

95 LOW HEIGHT NUT

78

78

15

92

11

37

50

46

51

25

BUTTON

HEAD

110

111

110

111

«
...
18
19
20
21
22
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: Hammer Pages: 22

Brand: Nautilus Pages: 26

Brand: Horizon Fitness Pages: 15

Brand: ParaBody Pages: 4

Ultimate Series

Brand: SoloStrength Pages: 15

Multi-gym UltraForce

Brand: Taurus Pages: 54

Brand: Calibre Fitness Pages: 8

Brand: XMark Fitness Pages: 14

Brand: Vectra Fitness Pages: 8

Brand: Adidas Pages: 9

Brand: Adidas Pages: 28

Brand: ParaBody Pages: 9

Profi Sit Up IN 1227

Brand: Insportline Pages: 8

Brand: Maxxus Pages: 5

Brand: Maxxus Pages: 28

Brand: Weider Pages: 24

Brand: Weider Pages: 24

Brand: Powerline Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands