ParaBody Parabody 660 User Manual Download Page 24 | Manualshive

Page: 24 / 51

background image

24

FIGURE 23

STEP 23

• Insert two 3/4” FLANGE BEARINGS (76) into the PRESS ARM (27) as shown in FIGURE 23.

• Hold the PRESS ARM (27) between the REAR (4) and MIDDLE UPRIGHTS (8) and slide the 3/4 DIA X 11” SHAFT (107) throught

the MIDDLE UPRIGHT (8), PRESS ARM (27), and through the collar on the REAR UPRIGHT (4). To

SECURE

the SHAFT (107) in

place, insert two 5/16” SET SCREWS (48) into the collars on the UPRIGHTS and tighten. See FIGURE 23.

• Insert two 1/2” FLANGE BEARINGS (78) into the PRESS ARM (27) as shown in FIGURE 23.

STEP 24

FIGURE 24

• Assemble the RECEIVING TUBE (13) to the PRESS ARM (27) using one 1/2 X 3” BOLT (87) and one 1/2” LOW HEIGHT LOCK NUT

(95).

(NOTE: Tighten the connection enough to remove play, yet allowing the PRESS ARM (2) to rotate freely.)

See FIGURE 24.

48

107

76

4

8

27

78

95 LOW HEIGHT NUT

27

13

87 1/2 X 3”

«
...
22
23
24
25
26
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: Marcy Pages: 14

Brand: Sunny Health & Fitness Pages: 9

Brand: Taurus Pages: 68

Brand: ParaBody Pages: 15

Brand: V-fit-ST Pages: 28

Brand: SPORTSTECH Pages: 112

Brand: X-plode Pages: 4

Brand: Orbit Pages: 29

Brand: ParaBody Pages: 10

Brand: Weider Pages: 24

Brand: Weider Pages: 24

Brand: Weider Pages: 25

Brand: Weider Pages: 28

Brand: WeiderPro Pages: 16

6900 831.14922.2

Brand: WeiderPro Pages: 32

Brand: TuffStuff Pages: 20

Brand: SPRI Pages: 2

IGNITE 07-71054

Brand: SPRI Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands