ParaBody Parabody 660 User Manual Download | Manualshive

Page: 23 / 51

background image

23

FIGURE 22

STEP 22

• CAREFULLY slide the PRESS ADJUSTMENT TUBE (22) into the RECEIVING TUBE (13).

(NOTE: Make sure the spring pin

barrel on the RECEIVING TUBE (13) is on the same side as the holes in the PRESS ADJUSTMENT TUBE (22).)

• Attach four PARAGLIDE STRIPS (62)

INSIDE

the end of the RECEIVING TUBE (13) and four PARAGLIDE STRIPS (62) to the

OUTSIDE

of the PRESS ADJUSTMENT TUBE (22) using the following steps:

• Thoroughly clean all sufaces where PARAGLIDE STRIPS (62) are to be attached.

• Remove the PARAGLIDE STRIPS (62) from the paper backing and firmly apply them to surfaces.

(NOTE: Orientate the

strips so they will slide by each other.)

• Insert two 1/2” FLANGE BEARINGS (78) into the COUNTER LEVER (3) as shown in FIGURE 22.

• Assemble the PRESS ADJUSTMENT TUBE (22) to the COUNTER LEVER (3) using one 1/2 X 3-1/2” BOLT (90) and one 1/2”

LOW HEIGHT LOCK NUT (95).

(NOTE: Tighten the connection enough to remove play, yet allowing the PRESS AD-

JUSTMENT TUBE (22) to rotate freely.)

1/2 X 3-1/2” 90

3

78

22

62

13

62

95 LOW
HEIGHT
NUT

• Thread one 3/8 X 1” BUTTON HEAD CAP SCREW (96) through the slot in the RECEIVING TUBE (13) and into the ADJUSTMENT
TUBE (22)

96 3/8 X 1”
BUTTON HD
CAP SCREW

«
...
21
22
23
24
25
...
»

Summary of Contents for Parabody 660




















































Reviews:

No comments

Related manuals for Parabody 660

Brand: York Fitness Pages: 21

Brand: ParaBody Pages: 9

Brand: Cap Strength Pages: 18

Brand: AsVIVA Pages: 59

Brand: Impex Pages: 13

Brand: Impex Pages: 14

Brand: OARTEC Pages: 24

Iron Grip Strength IGS-43

Brand: Impex Pages: 9

Iron Grip Sport IGS-02

Brand: Impex Pages: 10

Iron Grip Strength IGS-2110

Brand: Impex Pages: 12

Gym Dandy TT-320

Brand: Impex Pages: 15

Competitor WM-203

Brand: Impex Pages: 13

COMPETITOR WM-354

Brand: Impex Pages: 12

EVERLAST EVE-1000

Brand: Impex Pages: 23

Circuit Fitness AMZ-986RW

Brand: Impex Pages: 23

Brand: XMark Fitness Pages: 12

Brand: NordicTrack Pages: 27

Brand: Weider Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands