background image

9

8

User manual

Pandora DXL-1700L service-security system

Immobilizer mode

This mode is enabled by default, use a phone to disable this mode (see ‘Control over system via 

phone’ section). When engine is running, base unit of Pandora security system performs a search 

for immobilizer tags in radio zone. If no tags were detected, LCD remote will play ‘NO TAG FOUND’ 

ringtone. If no radio tags were detected when the ignition is switched on, the system will block 

the engine with all radio relays that were programmed into the system. Engine blocking will only 

occur when motion sensor detects movement of the car. If additional analogue blocking relays were 

installed, they will block the engine immediately, before or when the car starts moving, it depends 

on system settings.

Antihijack mode

This mode is disabled by default, use a phone to enable this mode (see ‘Change settings via 

phone’ section). Antihijack mode helps to prevent aggressive seizure of the car using delayed engine 

blocking on door opening.

Every time when the engine is running on opening/closing a door, immobilizer requests response 

from a remote using unique algorithm. After a door was opened while the engine is running, 

if the system cannot detect a radio tag, the engine will be stopped after 1 minute (general safety 

requirement). ‘ENGINE BLOCKING WARNING’ ringtone will play before blocking.

If engine blocking is performed via radio relay after warning signals are over or on new attempts 

to start the engine, immobilizer will only allow the engine to start when the car is not moving, and 

will block it again if it starts movement. Immobilizer will be in active mode in no more than 2 seconds 

after the ignition is switched on. If the car starts moving, the immobilizer will block the engine for 15 

seconds. When registered tag appears in the radio zone, blocking will be canceled and the system will 

return to the normal operation.

If the engine is blocked via analog relay, engine operation will be stopped after warning signals 

are over, until a registered tag appears in the radio zone or on registering movement – depending on 

the settings.

Immobilizer code using original car controls

Code immobilizer is a function that allows disarming and controlling timer channels using 

original car controls (button, lever or pedal). To enter immobilizer code, programmed button (lever, 

pedal) should be pressed a number of times equal the digit of the code. Pauses between presses 

should not exceed 1 second. Pauses more than 1 second will be interpreted as the start of next digit 

input. Immobilizer code can consist max of 4 digits from 1 to 9.

After entering a correct immobilizer code, depending on the settings, either the engine blocking 

will be lifted or a programmed timer channel will be activated.

Replacing immobilizer tag battery

Carefully open the cover of the tag’s battery compartment. Extract discharged battery and insert 

a new one keeping in mind the correct polarity. Replacing a battery will not cause a loss of tag code 

information, as authorization data is stored in the non-volatile memory of the MCU.

Carefully close the cover of the tag’s battery compartment. All elements of construction should be 

rigidly locked in places. If it is so, the tag can be operated as usually.

Control over system in case of emergency

Use a phone to deactivate the system quickly. To disarm the system via a phone, call the system’s 

number. When it answers, dial command 

0*

. If the call is not made from the owner’s number, guest 

PIN-code should be entered. Factory set guest PIN-code is 

1-2-3-4

. To switch off immobilizer RF tag/

Antihijack mode, dial command 

998*

 (after dialing, enter individual PIN-code that is located on the 

owner’s plastic card).

If the system cannot be deactivated via a phone, apply emergency disarming/switching off 

immobilizer RF tag using VALET button.

Emergency disarming/switching off immobilizer using VALET button

In case you cannot disarm the system using a remote, owner’s individual PIN-code can be used. 

Individual PIN-code is written on the owner’s plastic card under protective layer. Erase the protective 

layer and use VALET button to input PIN-code.

1. Using VALET button, input the first digit of the code (press the button a number of times, equal 

to the first digit; pauses between presses should not exceed 1 second). The system will confirm with 

Summary of Contents for DXL-1700L
























Reviews: