33
32
User manual
Pandora DXL-1700L service-security system
system will confirm correct PIN-code with red and green flashes of LED indicator and will memorize
PIN-code, then will proceed to the programming mode awaiting level input. Incorrect confirmation is
indicated with long red flash of LED indicator, after that the system will return to a programming mode.
4. Disarming via validator code.
The system can be disarmed by entering validator code using programmed button. It can be done
via a CAN-bus readable button (list of supported buttons can be viewed in status and command table
in AlarmStudio) or via any other button connected by analogue to ‘Code immobilizer (validator)’ input
programmed in the table of system inputs in AlarmStudio.
For example:
- when function is active, valuables can be left in the car;
- the system can be armed via VALET button; press and hold VALET button no less than 3 seconds,
the system will be armed in 30 seconds and locks will be closed;
- the system can be disarmed by entering validator code via open trunk button, after that locks will
be opened.
5. Additional authorization by entering validator code.
Validator (code immobilizer) is an additional car protection measure. Validator operation activates
all blocking relays (both analogue and digital ones).
To activate this function, enable ‘Switching off blockings only after entering validator code’. The
function will be activated automatically in 20 seconds after engine start and immediately when arming.
When engine starts, the system awaits validator code input. If code was not entered, the system will
activate all blocks via programming logic (on engine start, on moving automatic transmission selector/
switching off handbrake, on movement start).
When maintenance mode is active, validator will be deactivated.
To switch on maintenance mode:
- switch on the ignition;
- place the tag in radio coverage zone (if immobilizer/Antihijack is enabled);
- enter validator code;
- enable maintenance mode via the remote or by dialing DTMF command 551* and code from the
owner’s card.
To switch off maintenance mode via validator code:
- switch on the ignition;
- place the tag in radio coverage zone (if immobilizer/Antihijack is enabled);
- enter validator code;
- press validator button again 10 times in no less than 20 seconds after entering validator code.
Emergency switching off ‘Validator’ mode:
1. For emergency switching off this function call the system’s number and dial DTMF command
998* and code from the card.
2. This mode can be disabled by entering personal code from the plastic card on level 15 of
programming menu (see Level 15 description on page 33).
Level 12 Setting and updating GPS/GLONASS receiver NAV-035
To update the firmware of NAV-035 via the 2,4GHz wireless interface, run the GPS Loader software
and enter the programming level 12. After entering, update software of GPS/GLONASS receiver.
Level 15 Emergency disabling of immobilizer
To deactivate the immobilizer/Antihijack function enter the programming level 15, the system will
confirm the entering with green flash of LED indicator. Input the first digit of the secret code using
VALET button (press the button a number of times, equal to the first digit; pauses between presses
should not exceed 1 second). The system will confirm input with red flash of LED indicator. Enter the
other three digits in the same manner. The correct input will be confirmed with 2 short sound signals
of the siren and with red flash of LED indicator. To activate immobilizer/Antihijack function, enter
level 15, LED will confirm input with red flash. Press VALET button once, siren will emit 1 short beep.
Level 17 Setting up keyless bypass of built-in immobilizer
This level enters programming mode to teach algorithmic keyless bypass of built-in immobilizer.
LED indicator will be lit green when on this level. If system installation was performed correctly on
successful engine start using a key, LED indicator will flash green and siren will emit a short signal. To
save and finish, press VALET button. Now the system should be able to simulate key for remote starts.
For more in-depth instructions, use AlarmStudio.
Level 18 Programming DMS-100 sensor
Proceed to level 18, LED indicator will be lit green when on this level. Place the battery in the
sensor. If the recording was performed correctly, the base unit siren will emit a confirming signal. To
finish, press VALET button once.
