27
26
User manual
Pandora DXL-1700L service-security system
Wire 11 (Orange-black) (‘CAN1-Low’) It connects to appropriate CAN-Low wire of the car.
Wire 12 (Yellow-black) (‘CAN2-Low’/OUT-5) Factory setting is ‘Close central lock’. A negative
impulse of 0,8 seconds is formed on the wire to close central lock. Logic of the channel’s operation
can be set in the table of system outputs in AlarmStudio. Channel OUT-5 stops operating as an output
when a car code with enabled digital CAN2-bus is chosen.
Wire 13 (Blue-black) (OUT-3) Factory setting is ‘Blocking’. This wire is used to control external
analogue blocking relay with a normally open logic (it becomes grounded when switching on the
ignition and security system is not armed and radio tags are in range).
Wire 14 (Yellow) (INP-2) Factory setting is ‘Ignition’. This wire connects to ignition switch or to
appropriate wire where 12V voltage appears when ignition is switched on and doesn’t disappear until
the moment ignition is switched off. This input is multipurpose, it can operate in accordance with
selected logic.
Wire 15 (Purple) (‘siren’) It connects to siren control wire (+) (maximum load current is 2A).
Wire 16 (Red) (‘Power supply’ 12V) It should be connected to reliable conductor with constant
voltage of 12V.
Programming system and entering PIN-code
The system settings can be changed via computer. The system should be connected to a computer
via standard micro-USB cable and a special piece of software – Pandora AlarmStudio.
AlarmStudio can be downloaded from the official company web-site pandorainfo.com
Entering programming menu:
1. Disarm the system, switch off the ignition.
2. Connect the base unit of the system to a computer via micro-USB cable.
3. Using VALET button, input service PIN-code. Factory preset PIN-code is 1-1-1-1.
4. Using VALET button, input the first digit of the service code (press the button a number of times,
equal to the first digit; pauses between presses should not exceed 1 second). The system will confirm
entering of the first digit with red LED indicator flash.
WARNING!
IF YOU ARE AN INSTALLER, DO NOT ERASE PROTECTIVE LAYER OF THE OWNER’S
PLASTIC CARD! IN CASE A CUSTOMER COMPLAINS ON ERASED PROTECTIVE LAYER
OF THE CARD WITH THE INDIVIDUAL PIN-CODE, RE-INSTALLATION OF THE SYSTEM
IS CARRIED OUT AT THE EXPENSE OF THE INSTALLER.
5. Similarly input the second, third and fourth digit. Every input will be confirmed with red LED
flash.
6. The system will confirm correct PIN-code with red LED flashes and proceed to the programming
mode. If the input was incorrect, it will be indicated with long red flash and the system will proceed to
previous mode. New input can be attempted after 5 seconds.
Changing core settings via computer
The system allows programming all settings and updating software of the base unit via the
interface micro-USB cable or via radio channel using a computer. It does not matter, whether base
unit is installed into a vehicle or not. Software reads the current setting and allows changing them.
If base unit has not yet been installed in the vehicle, it should be powered via micro-USB cable while
programming. To program using a computer connected via cable, you need a standard micro-USB
cable, a computer with Windows and a special piece of software – Pandora AlarmStudio.
In preparation to the programming following stages should be followed:
• connect micro-USB cable to any free USB socket of the computer;
• start Pandora AlarmStudio (can be downloaded from the web-site);
• enter the programming settings mode by entering the service PIN-code on the base unit using
VALET button. Factory preset PIN-code is 1-1-1-1.
If the software configuration is carried out via the radio interface of 2,4 GHz, special USB programmer
RMP-03 should be used.
Configuring system settings via the wireless interface 2,4 GHz
To change the configuration of the system using a wireless interface 2,4 GHz, enter programming
level 10. The system will await a wireless connection from the computer for 2 minutes.
