31
30
User manual
Pandora DXL-1700L service-security system
The ignition should be switched off after recording. While on this programming level, you can
start and stop the engine many times – it will only be exited on VALET button press.
Level 4 Resetting to factory settings
To reset to the factory settings, you need to enter programming level 4, then press and hold
VALET button for 5 seconds until siren sounds. Once VALET button is released, the status indicator will
confirm a successful reset to factory settings with a long red flash.
Level 5 Programming of RHM engine compartment module
1. Enter programming mode on level 5.
2. Perform programming according to the instructions to the device (see on page 36).
Level 6, 7 Programming of radio relays 1 and 2
1. Select the desired level of the programming menu 6 or 7 for programming radio relays 1 or 2
respectively.
2. Connect the wire 3 of the radio relay to a grounded spot.
3. Apply power (+12V) on the contacts 2 and 4 of the radio relay. Siren will confirm radio relay
recording to the memory on level 6 with 2 beeps. Siren will confirm radio relay recording to the
memory on level 7 with 3 beeps.
4. After a successful radio relay recording, contact 2 should be disconnected and insulated,
contact 4 should be connected to the constant power supply 12V or to the wire where there is a
constant 12V when ignition is switched on.
Level 8 Recording GPS/GLONASS receiver Pandora NAV-035
Enter this level and connect power to the GPS/GLONASS receiver Pandora NAV-035. Siren of the
base unit will confirm successful recording with 1 beep.
Level 9 Recording of Pandora RW smart watches
Watches are recorded (paired) one by one. To pair the watches, press three functional buttons
simultaneously (on the watches) and hold them for 1 second (until a short beep), then release the
buttons. If the recording was successful, the base unit will emit 1 beep, after that you can move to
recording the next device. The pause between recordings of watches should not exceed 20 seconds.
WARNING!
IF THE CONTROL OVER SIREN IS CARRIED OUT USING ENGINE COMPARTMENT
MODULE RHM, SIRENS SOUND SIGNALS WILL NOT BE EMITTED DURING WATCHES
RECORDING!
To finish recording watches into the system, VALET button should be pressed again, the status
LED will produce series of red and green flashes; then switch on and off the ignition to leave the
programming mode.
Level 10 Configuring system settings via the wireless interface 2,4 GHz
To change the configuration of the system using a wireless interface 2,4 GHz, enter programming
level 10, the system will confirm the entering with red flash of LED indicator. The system will await
a wireless connection from the computer for 2 minutes. If the waiting time limit has expired and the
system was not connected to the computer, it will exit this level.
Level 11 Programming validator code of immobilizer (Pin to Drive)
1. Select the button to set the secret validator code of immobilizer.
To do this, enter level 11 of programming and press the selected button (e.g. wheel ‘volume up’
button), LED indicator will confirm input with orange flashes. If there are no orange flashes when any
button is pressed, then this button is not recognized by the system, select a different button. After the
button was chosen, press VALET button. Security system will memorize the last pressed button (which
was pressed before VALET button) as a button to enter PIN-code of immobilizer and will await input
of the first digit of PIN-code.
2. Program the immobilizer deactivation PIN-code.
Enter the first digit by pressing the previously selected button (pauses between presses must be
no more than 1 second). The base unit will confirm entering with red flash of LED indicator.
Input the second (third, fourth) digit by pressing the previously selected button. The base unit will
confirm entering with red flash of LED indicator.
Input the required number of digits (up to 4) and then press VALET button. The system will
confirm receiving of the secret validator code with long red flash of LED indicator and will expect for
confirmation of PIN-code.
3. Confirm the immobilizer deactivation PIN-code.
Input PIN-code again similarly to the programming procedure and press VALET button. The
