background image

Standard Features of the IntelliGuard 8000

System Components

The IntelliGuard 8000 kit contains the following components:

One Prewired 24-pin Connector Harness 

One PlainView 2 Coded Valet Switch

One Prewired 14-pin Connector Harness

One Medallion Siren

One IntelliGuard 8000 Control Unit

One Hardware Kit

One Digital Dual-Zone Proximity Sensor 4

One User’s Manual

Two Remote Transmitters

Two Window Decals

One Extended Range Receiver

One LED Status Indicator

 In tel liGuard 8000/299

1

q

Lifetime Warranty

q

His & Hers Remote Controls

q

ACG™ 2 (Anti-CodeGrabbing™)

q

Extended Range Receiver

q

Audible Low-Battery Warning

q

Built-In Two-Point Immobilizer™ 

q

Optional Wireless Immobilizer™

q

Digital Dual-Zone Proximity Sensor 4

q

Optional Remotely Adjustable OmniSensor 

q

Patented UltraSecure Coded Valet Mode™

q

Eight-Event TotalRecall™

q

Enhanced User-Selectable AutoArming

q

User-Selectable Remote Valet Mode Entry/Exit

q

Built-In BlackJax Anti-Carjacking System

q

Optional DataPort™ Interface and CliffNet Wizard

Pro™ Software

q

FACT — False Alarm Control and Test

q

Prewired LED, Sensor, Extended Range Receiver and

PlainView 2 Switch Connectors

q

High Output Medallion Siren

q

Dual-Mode “Chirp” Silencing

q

Remote Siren Silencing

q

Remote Door Locking/Unlocking with Built-in Relays

q

User-Selectable AutoLock 

q

User-Selectable AutoUnLock 

q

Integrated Electronic Timer

q

Turbo Timer Output 

q

CliffNet DataPort Accessory Interface

q

Remote Keyless Entry and Accessory Activation Even in

Valet Mode

q

Remote Panic with Smart Locking/Unlocking 

q

Smart Remote Trunk Release

q

Built-In Dual Parking Light Flasher with Onboard Relay

q

Remote-Controlled Courtesy Lighting

q

Patented Smart AutoTesting™ 

q

Patented Malfunction AutoBypass™ with

AutoReMonitoring

q

Patented Smart Prior Intrusion Attempt Alert

q

Patented Remote Control Code Learning and MultiRemote 

Recognition

q

Clear All Remotes

q

Multiple-Car Control

q

High-Luminescence LED Status Indicator with Automatic

Battery-Saving Mode

q

Multiple Sensor/Trigger Inputs

q

Patented SmartPowerUp™ 2

q

Full-Time SecureAccess™ Programming

q

Advanced CMOS Microcomputer

q

Pre-Loomed Wiring

q

Three Auxilliary Outputs with Selectable Output Types

q

AutoActivation of Auxilliary Output C for Window

All-Close

q

Installer-Selectable Door Ajar/Delayed Courtesy Lights

Summary of Contents for IntelliGuard 8000



















Reviews: