9
9.
①
sw
②
③
pre
9.
Co
ter
9.
We
ma
9.
Re
9.
①
W
To
wa
ins
* W
rot
②
U
Us
coo
Th
③
If t
fun
1)
2)
3)
ma
4)
aro
5)
Be
po
Cautio
1 Operat
When the p
witch is turned
After finishi
The power
essing of the
2 Conne
onnect only o
rminal, this m
3 Radio i
elding somet
anufacturer's
4 Warnin
efer to the Tro
5 Flow sw
Water pressu
protect the
ater warning
stall the wate
When the wa
tation of pum
Use of an an
se glycol typ
oling water i
e ratio of ant
Maintenanc
the flow swit
nction proper
Remove righ
Remove wat
Remove cap
ain body.
Clean fur an
ound axis an
Replace the
ecause of fre
wer supply o
on
tion of po
power switch
d on again w
ng work, wai
switch mus
e torch switch
ction of
one torch, ho
may cause a
interfere
times cause
s agent to pu
ng lamp
oubleshootin
witchRef
ure
water coole
lamp and ter
er tank (YX-0
ater tank is u
mp motor or c
ntifreeze solu
e for antifre
ncreases ca
tifreeze solut
ce of flow sw
ch is used fo
rly. Clean the
ht side panel
ter inlet fixtu
p on the flow
nd rust accum
nd float.
cap to the m
eezing, the f
or keep wate
ower sw
h trips out, it
without remov
it for two or t
st be turned
h may result
torch, ho
older or cab
short circuit
ence
s radio inter
rchase acce
ng Guide if th
fer to the
ed torch from
rminals work
0092UW) to e
used, change
cause obstru
ution
eze solution
ausing reduct
tion should b
witch
or a long pe
e flow switch
l.
re nut.
w switchupper
mulated in th
mainbody, (T
flow switch m
r flowing at v
itch (on
t must not b
ving the caus
three minutes
off when ch
in electric sh
older and
le to each o
accident or i
rference. If in
ssory noise f
he warning la
e followi
m burning, th
k where wate
ensure neces
e cooling wa
ction to wate
n. However,
tion in flow a
be less than
riod, its axis
periodically.
r section from
e flow switch
ighten it by h
may be brok
very low pres
23
the front
be turned on
se, it may res
s before turn
hecking or r
hock.
d cable t
output termin
neffective ar
nterference i
filter.
amp lights.
ng table
he machine
er flow rate is
ssary flow.
ater once or
er passages
if mixing rat
and the flow
20%.
s and float w
. 1) Remove
m the
h and
hand.)
ken in winter
ssure.
t panel o
again. Con
sult in burn-o
ning off the p
replacing the
to output
al. If two or
rc start becau
is generated
for tung
is provided
s too low. If th
twice every
of the torch a
tion of antifre
switch may
will develop fu
right side pa
r. Therefore,
of machin
tact manufa
out of the ma
ower switch.
e torch com
t termina
three cables
use of high f
d in a radio o
gsten ele
with a flow
his happens
six months.
and the flow
eeze solutio
be activated
ur or rust. As
anel.
Disconnect
ne)
cturer's agen
achine.
.
ponent beca
als
s are connec
frequency wa
or other equ
ectrode.
switch, whic
, increase wa
. Accumulate
switch.
on is increas
d to stop we
s a result, th
torch water
nt. If the pow
ause erroneo
cted to a sin
ave leakage.
ipment, cons
ch activates
ater flow rate
ed fur may s
ed, viscosity
lding operati
he float may
r hose from
wer
ous
ngle
sult
the
e or
stop
y of
ion.
not
the
Summary of Contents for YC-400TX4
