manualshive.com logo in svg

Panasonic U-4LE1R8, Service Manual

Share
Download
Panasonic U-4LE1R8 Service Manual Download Page 99

Mini VRF SYSTEM

PCB Settings

4

1. Outdoor Unit Control PCB 

4-7

 LED1, 2
(D302, D303)

LED (red × 2) 

LED 1 and 2 blink alternately while automatic address setting is in progress.

Display the alarm contents for alarms that are detected by the outdoor unit.

•

•

Power LED
(D514)

LED (green): Power indicator
Indicates the DC 5V power on the outdoor unit control PCB.

 RUN

2P plug : Start pin
Short-circuit this pin and apply a pulse signal to start all indoor units in that refrigerant 
system.

 STOP

2P plug : Stop pin
Short-circuit this pin and apply a pulse signal to stop all indoor units in that refrigerant 
system.

CHK

2P plug (black)
Short-circuit during the test run operation. 
Open the circuit after the test run.

SILENT
(CN-SILENT)

2P plug (White) : Socket for silent mode

CN-OPTION 1, 2

Plug for Demand Terminal (optional CZ-CAPDC3)

Used for installing the external timer for the silent mode.
(Refer to the section 1-14. Servicing and Maintenance Functions in service manual.)

 AP

2P plug : Vacuuming pin

To perform vacuuming of the outdoor unit, short-circuit this pin and then turn the 
power ON. All solenoid valves turn ON and vacuuming begins smoothly. (Do not 
perform automatic address setting at this time.)

Release the short-circuit to return the unit to normal status.

•

•

MODE

2P plug : Indoor unit Heating/Cooling mode change pin

When operating the compressors to perform automatic address setting, operation 
in Heating mode can be normally used. However, short-circuiting this pin performs 
operation in Cooling mode. (Static signal)

Short-circuiting this pin during ordinary operation changes the mode from Cooling 
to Heating (if the current mode is Cooling) or from Heating to Cooling (if the 
current mode is Heating).

•

•

TEST

2P plug 

This pin is used to test the PCB at the factory.

When the power is turned ON after this pin has been short-circuited, all output 
signals will be output in sequence. (Sequential output does not occur if this pin is 
short-circuited when the power is already ON.) Releasing this pin returns the unit 
to normal control.

•

•

SM830209-00̲Mini̲VRF SYS.indb   7

SM830209-00̲Mini̲VRF SYS.indb   7

2012/01/11   18:26:37

2012/01/11   18:26:37

Summary of Contents for U-4LE1R8
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands