manualshive.com logo in svg

Panasonic U-4LE1R8, Service Manual

Share
Download
Panasonic U-4LE1R8 Service Manual Download Page 57

Mini VRF SYSTEM

Trouble Diagnosis

3

3-17

3. Mini VRF System Alarm Codes

E08 Duplicate Indoor Unit Address Settings Error

Error Detection Method

Error Diagnosis

It is judged an error if the addresses of indoor units are duplicated.

The ‘/’ in the table indicates the DC motor’s indoor unit board/AC motor’s indoor unit board.

•

For information on the procedures for replacing the nonvolatile memory (EEPROM) of the indoor unit, refer to the manual
that is packaged with the indoor unit service board.

•

1.

2.

1

The indoor unit address settings are duplicated in the remote control detailed settings mode.
The multiple unit DISP pin is shorted across the indoor unit whose address is Not Set.

•
•

Remove the short

1-2

Is the DISP pin on the indoor unit control PC board shorted?

1-1

Conduct checks prior to auto address setting.
Does E08 fail to go off even after running auto address setting again?

1-2

 

1-3

1-4

Yes

Yes

No

No

1-3

Do not make changes to indoor unit addresses with the detailed settings of the remote 
controller.
Make them in the remote control address change mode.

1-4

Indoor
unit
control
PC board

The nonvolatile memory (EEPROM) on the indoor unit board has failed.

Replace the EEPROM.

EEPROM

EEPROM

DC Motor Model Indoor Unit Control PC Board

AC Motor Model Indoor Unit Control PC Board

DISP Pin

DISP Pin

SM830209-00̲Mini̲VRF SYS.indb   17

SM830209-00̲Mini̲VRF SYS.indb   17

2012/01/11   18:25:06

2012/01/11   18:25:06

Summary of Contents for U-4LE1R8
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands