Panasonic U-4LE1R8 Service Manual Download Page 113

Page: 113 / 119

Mini VRF SYSTEM

Service Checker

1. Outdoor Unit Maintenance Remote Controller

6-9

1-4. Monitoring Operations

Displays the indoor unit and outdoor unit sensor
temperatures.
<Operating procedure>

➀

Press and hold the

(CHECK) and

(CANCEL) buttons simultaneously for 4 seconds or
longer to engage temperature monitor mode.
During temperature monitoring,

(CHECK) illuminates.

(The display and operations are the same as for monitor
mode using the indoor unit remote controller.)

➁

Press the

(UNIT) button and select the indoor

unit to monitor.

➂

Press the temperature setting

buttons

and select the item code of the temperature to monitor.
The unit No. of the selected indoor unit, and the
temperature data, are displayed.

➃

To end monitoring, press the

(CHECK) button. The display returns to normal display mode.

NOTE

The display does not blink.

SM830209-00̲Mini̲VRF SYS.indb 9

2012/01/11 18:26:46

Summary of Contents for U-4LE1R8
























































































































Search results

Summary of Contents for U-4LE1R8

Reviews:

Brands by name

Popular brands

Panasonic U-4LE1R8, Service Manual

Search results

Summary of Contents for U-4LE1R8

Reviews:

Brands by name

Popular brands