manualshive.com logo in svg

Panasonic U-4LE1R8, Service Manual

Share
Download
Panasonic U-4LE1R8 Service Manual Download Page 102

Mini VRF SYSTEM

Self-Diagnostics Function Table

5

1. Self-Diagnostics Function Table

5-2

Self-Diagnostics Function Table

Causes and corrections in instances when automatic address setting cannot be started.

 Trouble  

 Cause and correction  

The power LED on the outdoor unit control PCB does 
not turn ON.  

Check for any errors in the power wiring to the outdoor 
unit, and check for a missing phase.

LED 1 and 2 on the outdoor unit control PCB do not 
turn OFF when the outdoor unit power is turned ON, 
and automatic address setting cannot be started.

Check the “Alarm Displays” table and correct the 
problem.

An alarm appears immediately when automatic 
address setting is started from the remote controller.

Nothing happens when the operator attempts to start 
automatic address setting from the remote controller.

Check that the remote controller wiring and the inter-
unit control wiring are connected correctly.
Check that the indoor unit power is ON.

Causes and corrections in instances when automatic address setting starts, but cannot be completed successfully.

 Trouble  

 Cause and correction  

An alarm appears on the remote controller sometime 
from several seconds to several minutes after 
automatic address setting is started.

Check the “Alarm Displays” table and correct the 
problem.

LED 1 and 2 on the outdoor unit control PCB indicate 
that automatic address setting is in progress (the LEDs 
blink alternately) for several minutes after automatic 
address setting is started (the compressors may also 
start and stop several times), however LED 1 and 
2 never indicate that automatic address setting is 
completed (turn OFF).

Check the alarm details on the “Outdoor Unit Control 
PCB LED 1 and 2 Alarms” table, then check the “Alarm 
Displays” table and correct the problem.

If alarm E15, E16, or E20 appears after automatic address setting is started, check the following items.

 Alarm display  

 Alarm description  

 E15  

The number of indoor units detected during automatic address setting was smaller than the 
number of indoor units which was set with switch S004 on the outdoor unit PCB.  

 E16  

The number of indoor units detected during automatic address setting was larger than the 
number of indoor units which was set with switch S004 on the outdoor unit PCB.  

 E20  

The outdoor unit received no serial signals from indoor units within 90 seconds after 
automatic address setting was started.  

•

•

•

SM830209-00̲Mini̲VRF SYS.indb   2

SM830209-00̲Mini̲VRF SYS.indb   2

2012/01/11   18:26:39

2012/01/11   18:26:39

Summary of Contents for U-4LE1R8
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands