manualshive.com logo in svg

Panasonic U-4LE1R8, Service Manual

Share
Download
Panasonic U-4LE1R8 Service Manual Download Page 43

Mini VRF SYSTEM

Trouble Diagnosis

3

3-3

1. Contents of Remote Controller Switch Alarm Display

ON:

Blinking:

OFF:

Possible cause of malfunction

Activation of
protective
device

Thermistor
fault

EEPROM on indoor unit PCB failure

Protective
device for
compressor is
activated

Protective device for 
compressor is activated.

Protective device in outdoor 
unit is activated.

Indoor thermistor is either
open or damaged.

Outdoor thermistor is either
open or damaged.

High-pressure switch

Incorrect discharge temperature (Comp.)

Power supply circuit failure, missing-phase detection

There is a trouble with the outdoor unit when the liquid valve 
and the gas valve are closed.

Outdoor unit fan motor is unusual.

Compressor running failure resulting from missing phase in the 
compressor wiring, etc. (Start failure not caused by IPM or no gas.)

Missing-phase/reverse-phase in the compressor wiring, 
Compressor start-up failure (Overcurrent at time of INV 
compressor starts up, etc.)

IPM trip (IPM current or temperature)

Indoor coil temp. sensor (E1)

Indoor coil temp. sensor (E3)

Indoor suction air (room) temp. sensor (TA)

Indoor discharge air temp. sensor (BL)

Comp. discharge gas temp. sensor (TD)

Outdoor coil liquid temp. sensor (C1)

Outdoor air temp. sensor (TO)

Compressor intake port temperature sensor (TS)

High pressure sensor

EEPROM on the outdoor unit PCB has failed.

Power supply current (CT) sensor failure 
(Current is not detected at time of compressor ON.)

Overcurrent of power supply current (CT) sensor

PAM failure

P13

P05

P04

P03

P16

P22

P29

H31

<<F01>>

<<F03>>

<<F10>>

<<F11>>

F04

F07

F08

F12

F16

F29

F31

H03

H02

H01

Operation

Standby

for heating

Wired
remote
control
display

Wireless

remote controller

receiver display

Timer

Timer lamp blinking

Timer lamp blinking

Operating and 
timer lamp blinking
simultaneously

Operating and 
timer lamp blinking
simultaneously

Operating and 
heating ready 
lamp blinking
altemately

Operating and
timer lamps 
blinking alternately

Operating and
timer lamps 
blinking alternately

SM830209-00̲Mini̲VRF SYS.indb   3

SM830209-00̲Mini̲VRF SYS.indb   3

2012/01/11   18:24:29

2012/01/11   18:24:29

Summary of Contents for U-4LE1R8
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands