manualshive.com logo in svg

Panasonic U-4LE1R8, Service Manual

Share
Download
Panasonic U-4LE1R8 Service Manual Download Page 55

Mini VRF SYSTEM

Trouble Diagnosis

3

3-15

3. Mini VRF System Alarm Codes

E06 Error in the Outdoor Unit Receiving Signal from the Indoor Unit

Error Detection Method

(When indoor unit(s) are connected)

Error Diagnosis

It is judged an error when there is no transmission (reply) from the indoor unit to the outdoor unit for a period of three minutes.

The ‘/’ in the table indicates the DC motor’s indoor unit board/AC motor’s indoor unit board.

•

There is no TEST pin on the AC motor’s indoor unit board.

•

For information on the procedures for replacing the indoor unit’s control board, refer to the manual that is packaged with
the indoor unit control PCB.

•

1.

2.

3

Remove the short

3-2

Are the DISP pin and/or CHK pin on the indoor unit control PC board 
short-circuited?

Is the indoor unit powered off?

1-1

Is the indoor/outdoor operation line shorted, opened, 
grounded or has a wrong contact? 

2-1

3-1

Is the wireless remote controller and/or optional control PC board 
connected to on the indoor unit’s control PC board?

3-2

Power on

2-1

Correct the wiring

3-1

 

 

3-3

3-5

Yes

Yes

Yes

No

No

No

Disconnect the connector mentioned above on the control PC board
of the indoor unit control PC board, and see whether the E06 goes off
after several minutes. (When doing so, if two remote controllers are 
being used and the wireless remote controller is the main remote 
controller, set the other remote controller as the main.)

3-3

Replace all optional control PC board and/or wireless remote control parts including wiring.

3-4

3-5

3-4

3-5

Yes

No

Indoor 
units
control 
PC board

1 Indoor unit

power

2 Indoor/

outdoor 
operation 
line

Yes

No

The indoor unit is not turned on.
The DISP pin of the indoor unit is shorted.

The signal output control PC board (optional control PC board) inside the indoor unit has failed.

•
•

•

There is a short, open, wrong contact or grounding of the indoor/outdoor operation line.

•

The thermistor inside the indoor unit is grounded.

•

Indoor unit control PC board failure

Replace board.

RC

OPTION    

OPTION

CHK Pin

CHK Pin

DC Motor Model Indoor unit Control PC Board

AC Motor Model Indoor unit Control PC Board

DISP Pin

RC

DISP Pin

SM830209-00̲Mini̲VRF SYS.indb   15

SM830209-00̲Mini̲VRF SYS.indb   15

2012/01/11   18:24:53

2012/01/11   18:24:53

Summary of Contents for U-4LE1R8
























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands