Panasonic TY-SP42PM3W Installation Manual Download

Page: 50 / 59

Mount the display in the ceiling unit.

Hook the display’s top insulating spacers in the ceiling unit by aligning
the display with the notches in the ceiling unit and sliding the display
downward.

Insert the bottom insulating spacers by lifting the display slightly, fitting
the bottom spacers into the holes, and then lowering the display.

W h e n m o u n t i n g t h e
display in the ceiling unit,
be sure the ceiling unit is
straight and not at an
angle.

Fixing screw (M5) 1 each
left and right sides

Do not lift the display too high. It may come unhooked from the unit.

Install the fixing screws
on the left and right to
prevent the display from
sliding out of the ceiling
unit.

Fix the display.

Install two fixing screws (M5, included) in the corresponding holes on the
ceiling unit (left and right).

Insulating spacer

Notch

Fixing screw (M5) x 2

Summary of Contents for TY-SP42PM3W




























































Search results

Summary of Contents for TY-SP42PM3W

Reviews:

Related manuals for TY-SP42PM3W

Brands by name

Popular brands

Panasonic TY-SP42PM3W, Installation Manual

Search results

Summary of Contents for TY-SP42PM3W

Reviews:

Related manuals for TY-SP42PM3W

Brands by name

Popular brands