Panasonic TY-SP42PM3W Installation Manual Download

Page: 47 / 59

Flat washer
(not supplied)

Spring washer
(not supplied)

M12 bolt
(not supplied)

Earthed mains extension lead
(example)

Signal cable
(example)

• Reinforce the ceiling if it is not strong enough.
• Use bolts appropriate for the ceiling material (not supplied).
• Refer to the installing examples for wooden structure and concrete structure.

M12 bolt

Spring washer

Flat washer

curled plug(M12)

Anchor nut or

Concrete

Installing to a concrete structure(example)

Installing to a wooden structure(example)

M12 bolt

Spring washer

Flat washer

Nut

Beam

" ] )

(min.thickness 40mm [1

Mounting plate

Ceiling board

Nail

Installation the ceiling unit.

Attach the ceiling unit (upper section)

1) Before installing the upper section, pull the wiring through the pipe.

Use an earthed mains extension lead (not supplied).

2) Make holes in the ceiling using a method appropriate for the ceiling

structure and for inserting M12mm bolts. Install the upper section
using a hex socket bolt (M12 not supplied), flat washer and spring
washer.

Summary of Contents for TY-SP42PM3W




























































Search results

Summary of Contents for TY-SP42PM3W

Reviews:

Related manuals for TY-SP42PM3W

Brands by name

Popular brands

Panasonic TY-SP42PM3W, Installation Manual

Search results

Summary of Contents for TY-SP42PM3W

Reviews:

Related manuals for TY-SP42PM3W

Brands by name

Popular brands