manualshive.com logo in svg

Panasonic Section 700, User Manual

Share
Download
Panasonic Section 700 User Manual Download Page 291

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

  Page A-1

 Appendix A: CPC-EX 1.0 Updates

CPC-EX Version 1.0 (and above) offers the following enhancements to the 
DBS phone system:

Compatibility

CPC-EX Version 1.0 supports all features of CPC-B Version 7.1 (with the exception of 
TSAPI support). In addition, CPC-EX Version 1.0 adds support for additional features, 
including the 44-Series phones, T1 Networking, and ISDN.

The CPC-EX card can be installed into an existing DBS cabinet, with no hardware 
modifications.

CPC-EX software uses existing CPC-B programming addresses, with the same numbering. 
Additional addresses have been added for CPC-EX features.

Note:

 CPC-EX requires SCC-B.

44-Series Phone Support

CPC-EX provides full support for Panasonic’s 44-Series phones (VB-44xxx). Table 1 below 
lists all 44-Series phone models and their part numbers. Most models are available in two 
colors: gray and black.

 Table A-1. 44-Series Phones 

16-Key Phone  (gray)

VB-44210G

16-Key Phone  (black)

VB-44210B

16-Key Speakerphone  (gray only)

VB-44211G

22-Key Phone  (gray only)

VB-44220G

22-Key Small-Display Speakerphone  (gray)

VB-44223G

22-Key Small-Display Speakerphone  (black)

VB-44223B

34-Key Small-Display Phone  (gray only)

VB-44230G

34-Key Small-Display Speakerphone  (gray)

VB-44233G

34-Key Small-Display Speakerphone  (black)

VB-44233B

22-Key Large-Display Speakerphone  (gray)

VB-44225G

22-Key Large-Display Speakerphone  (black)

VB-44225B

DSS/72 Console  (gray)

VB-44320G

DSS/72 Console  (black)

VB-44320B

EM/24 Unit  (gray)

VB-44310G

EM/24 Unit  (black)

VB-44310B

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands