Home
/
Panasonic
/
Section 700
/
User Manual

Panasonic Section 700, User Manual

Share

Page: 132 / 394

Panasonic Section 700 User Manual Download Page 132

Chapter 4. Key Telephone Features

Section 700 - Operation

4-16

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• Voice calls do not forward when Call Forwarding--No Answer is used.

• If several calls arrive at once at an extension set for Call Forwarding-No

Answer, all of the calls will be queued. (The timing for each call begins
with the ringing tone.)

• Extensions for which Call Forwarding-External has been set

cannot

:

- Be in the middle of an outside call when the feature is activated.

- Have a toll restriction setting that prohibits outside calls.

• Calls can be forwarded to a third-party voice mail using the “Call Forward

ID Code” described on page 3-13.

• Beginning with CPC-AII and CPC-B Version 7.0, all call forwarding types

(All Calls, Busy/No Answer, Busy, and No Answer) can be forwarded
outside using speed dials. However, if Least Cost Routing is activated, dial
“9” trunks cannot be used. Select another trunk group instead (81-86). See
“Speed Dialing” on page 4-88 for more information on programming
speed dial numbers.

• If Forced Least Cost Routing is activated, trunk groups 81-86 are not

available.

• Calls cannot be forwarded to an extension in DND.

«
...
130
131
132
133
134
...
»

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands