Panasonic Section 700 User Manual Download Page 205

Page: 205 / 394

Section 700 - Operation

Chapter 4. Key Telephone Features

DBS-2.3/9.2-700

DBS Manual - Revised April 2000

4-89

Operation

To assign Personal Speed Dialing:

1. Press

ON/OFF

2. Press

PROG

3. Press a One-Touch key or press

AUTO

followed by the personal speed

dial bin number (90-99 or 900-909).

4. If you want to include a trunk access code in the number, press

CONF

then 9 or 1~6. (1-6 = trunk groups 81-86.)

If you enter a trunk access code in the speed dial number, you do not have
to open a trunk before using the number.

5. Dial the number.

6. Press

HOLD

7. Press

ON/OFF

To use a programmed Personal Speed Dial key:

1. If the Speed Dial key includes a trunk access code, simply press the key.

If the Speed Dial key does not include an access code, press an unlit line
key before pressing the Speed Dial key.

• The phone issues outside dial tone.

• The line LED lights green.

• “CO TALK #XX” (where “XX” is the line number) appears on the

display.

2. Complete your call and replace the handset.

The line LED changes from green to red and then goes off.

To check a programmed Personal Speed Dial key:

1. Press

the

ON/OFF

key:

• The phone issues intercom dial tone.

• The

ON/OFF

LED lights.

Summary of Contents for Section 700











































































































































































































































































































































































































Search results

Summary of Contents for Section 700

Reviews:

Brands by name

Popular brands

Panasonic Section 700, User Manual

Search results

Summary of Contents for Section 700

Reviews:

Brands by name

Popular brands