Panasonic PV-D4733S-K, Service Manual

Page: 269 / 274

TROUBLESHOOTING HINTS
PV-D4733S/PV-D4743/PV-D4743S/PV-D4743S-K
How to confirm whether DVD circuit or other circuits is defective.
1) Confirm DVD operation and VCR operation
OK
OK
Playback the test DVD disc.
The Message "PLEASE CHECK THE DISC, AND
FOR STAINS OR SCRATCHES ON DISC" appears.
Confirm communication between DVD Main C.B.A.
and Main C.B.A. by referring to "Communication Timing
Chart 2."
Confirm that the OPEN/CLOSE TRAY works correctly.
Check points:
Pin 91 of IC6001 on the Main C.B.A.
(DVD_POWER_ON(H))
300 ms
1. Output Signal from DVD Main C.B.A.
(TP8003 (DVD_SCK) on the DVD Main C.B.A.)
Troubleshooting Hints
DVD Main C.B.A. is defective. NG
Repair the DVD Main C.B.A.
IC8001 or the circuit around it is defective.
DVD Mechanism Unit or IC8801 is defective.
DVD Mechanism Unit or IC8801 or IC8001 is defective.
NG
Repair it by referring to the "Cause: Tray Problem. "
DVD Mechanism Unit is defective.
Replace the DVD Mechanism Unit.
Repair it referring to "Cause: Spindle Motor Problem,"
and "Cause: Traverse Problem," "Cause: Pickup
Problem."
If there is problem with audio
or picture, even though it plays
back.
DVD Main C.B.A. is defective.
Repair DVD Main C.B.A.
1. Playback a VHS tape.
DVD circuit is defective.
Main C.B.A. is defective. Both NG
No PB VCR only
No PB DVD only
How to confirm whether DVD Mechanism Unit or DVD Main C.B.A. is defective.
NOTE:
Host communication may not occur correctly between IC6001 on the Main C.B.A. and IC8001 on the DVD Main C.B.A.
when there is a problem on the DVD Main C.B.A.
This is because the unit automatically switched to VCR mode after approx. 30 seconds even in DVD mode because the
DVD Main C.B.A. shuts down. (Check the VCR mode indicator and DVD mode indicator on the Multi Function Display.)
Check the voltage during the 30 seconds during which the unit remains in DVD mode.
First, confirm that the Main C.B.A. is O.K. other than DVD
Mechanism Unit and DVD Main C.B.A. by referring to
"Communication Timing Chart 1," and "Communication
Timing Chart 2."
Check points:
1. All Power Supply Voltages for DVD circuit
(TP8016 (SW_3.3V_DVD), TP8414 (SW_5V_DVD),
Pin1 of P8402 (M_VM_6V), Pin2 of P8402 (ACT_VM_5V)
on the DVD Main C.B.A.)
2. Output Signal from DVD Main C.B.A.(TP8006 (D_RDY)),
Output Signal from Main C.B.A.(TP8002 (H_RDY))
(TP8006 (D_RDY), TP8002 (H_RDY) on the DVD Main C.B.A.)
2. Playback a DVD disc. Repair the Main C.B.A.
Main C.B.A. is defective. NG
Repair the Main C.B.A.
Main C.B.A. is defective.
Repair the Main C.B.A.
Perform troubleshooting referring to "How to confirm whether DVD Mechanism Unit or DVD Main C.B.A. is defective."
Troubleshooting Hints of DVD Mechanism Unit
Cause: Tray Problem
Check the signal at Pin2 of CN9852 (+) on the DVD Sub
C.B.A. (3.0 Vp-p)
Check the signal at TP8809 (TRYIN) on the DVD Main
C.B.A.
NG
OK
IC8801 on the DVD Main C.B.A. is defective.
Replace IC8801 on the DVD Main C.B.A.
IC8001 on the DVD Main C.B.A. is defective.
Replace IC8001 on the DVD Main C.B.A.
OK
NG
Communication Timing Chart 1
Communication Timing Chart 2
TP8007 on the DVD Main C.B.A.
(DVD_RESET(L))
TP8002 on the DVD Main C.B.A.
(H_RDY (VCR DVD)
2 s
DVD SERIAL START
DVD SERIAL START
16 ms
1 ms
MAX 1.5 ms
16151413121110 9 8 7 6 5 4 3 2 1
TP8006 on the DVD Main C.B.A.
(D_RDY (DVD VCR)
TP8003 on the DVD Main C.B.A.
(DVD_SCK (DVD VCR)
Pin2 of )
(During Loading)
Pin2 of )
(During Unloading)
TP8809
(During Loading)
TP8809
(During Unloading)
OK
Note:
If PR1502 on the Main C.B.A. becomes defective
again after replacement, replace both DVD
Mechanism Unit and IC8801 on the DVD Main
C.B.A. at thesame time.
1 V 1 V
1 V 10 us
V1 2.3 Vp-p V1 1.0 Vp-p
1 V 1 V
V1 2.3 Vp-p V1 1.0 Vp-p
10 s 10 s
10 s 10 s