Panasonic NV-HS1000, Service Manual

Page: 37 / 138

•
ShowView Programming
Programming Is now easier than ever: simply enter the
ShowView number provided in the programme schedule
· cclumn carried by newspapers and magazines.
ShowView numbers are numbers which are assigned to
each programme listed in the TV programme schedule
carried In newspapers and TV guides. When these
numbers are entered and TRANSMIT Is pressed, the
numbers are converted Into the actual programming and
sent to the VTR.
4
5
4
3
28
·preparation
• Insert a cassette tape with an Intact erasure prevention
tab.
•Set the programme positions on both the VTR and remote
ccntroller as showA on pages 12-15.
Operations
Display Symbols
1
2
3
4
5
6
Open the door of the remote controller.
VTRO
'X'i'ID CfC
a,
Press
SHOWVIEW.
u
1:
..
:��--,
Enter a ShowView number.
Example: 920216 vm,
:;:;;
Press
CONFIRM
to check that the
number corresponds to the right
programme.
CONFIRM
VTRO
SU
C)
,:,:�
0
:
ig:
:a
i9:ss
•To make any �orrectlons, use buttons
0-0-
Press
TRANSMIT.
On Screen Display
-
o, OFT
1100 11.30 SI'
10lll 11:00 tP
1�'011
1100 S,
22:I� Zl.30 I.I'
:1002 21::l<l !I
Close the door of the remote controller.
Noles:
•To select the desired tape speed, press RECORDING
SP/LP lri any of steps 3-4.
•To cancel the PDCNPS function, press PDCNPS In any
of steps 2-4.
•When the ShowView number Is used for programming,
the recording time may be slightly longer than the actual
programme time.
•Repeat steps 2 to 4 If "Err" appears on the remote
controller.
•When programming two or more programmes, repeat
steps2to 5.
•The procedures for checking and cancelling whatever has
been programmed are the same as for remote ccntrol
programming.
Other Functions
VHS Index Search System
It Is very easy to find the beginning of each recording,
because a special index signal is recorded at the start of
each recorded segment on the tape.
For example:
Searching for the 2nd recorded segment In the forward
direction.
Press INDEX
►
Ii-I twice.
s
n-,
I I .J
I II
UL
•After finding the specific recorded segment, playback
starts automatically.
• For fhe reverse direction, press INDEX 1-C
◄
.
•Up to 20 programmes can be searched for In both
directions.
Recording Index Signals
Index signals. are recorded In following cases.
WRITE Indicator appears on the Display.
•When a recording is started by pressing REC.
•When REC Is pressed during recording.
•When timer recording is activated.
• When WRITE Is pressed during playback.
Erasing Index Signals
1 Search the Index signal to be erased by pressing INDEX
►
l>-lor l""'◄
.
•Be sure not to omtt this step. Otherwise, this function
may not work correctly.
2 Press PAUSE/STILL when playback starts.
3 Press ERASE.
•Erasing Is possible during playback if ERASE Is
pressed during the five seconds following the Index
signal.
Notes:
•The index search function can only work correctly, if the
Index signals are spaced at least 3 minutes apart In the
SP mode and 5 minutes apart In the LP mode.
•Index signals can not be recorded or erased on a video
cassette with a broken olf tab.
On Screen Dfsplay
Press OSD lo make the On Screen Display appear on the
TV screen.
•To make this display disappear, press OSD again.
C)
YISS WAITE
Note:
On Screen Display will not appear during NTSC playback.
29
Timer Recording
Other Functions
LJLJ
0
Programme position
e
Present time
E)
Tape counter
0
Cassette-In Indicator
0
Tape speed Indicator
0
Tape running display
Slop, Eject
•
Rewind, Review
◄◄
Fast Forward, Cue ►►
Playback
►
Reverse Playback
◄
Still Playback
II
Recording, Insert, Audio Dubbing
•
Recording Pause, Insert Pause,
...
Audio Dubbing Pause
Slow Playback
I
►
Reverse Slow Playback ◄
I
0
Index signal writing or erasing Indicator