Panasonic KX-TVS90 Page 36 Installation Manual Download | Manualshive

Page: 36 / 410

background image

INSTALLATION

36

Installation Manual

2.7

TERMINAL CONNECTION

2.7.1

Requirements for Connecting Programming Terminal

The programming terminal must be connected with a serial cable with an RS-232C connector
at the RS-232C port. This must be a null modem cable. This enables system administration
(system setup, mailbox setup, and system diagnosis) to be performed.

Communication parameters of the VPS have been set to the following values at the factory:

2.7.2

Connecting the RS-232C Cable

RECOMMENDED:

Before connecting the cable, switch off the power on both the data terminal and the VPS.

Insert the RS-232C cable into the VPS with the connector indicating the same direction.

The cable must be shielded and no longer than 2 m {6.5 feet}.

Table 6

COMMUNICATION PARAMETERS

Baud Rate:

9600 bps

Word Bit Length:

8 Bits

Parity:

None

Stop Bit Length:

1 Bit

POWER

VOICE PROCESSING SYSTEM

«
...
34
35
36
37
38
...
»

Summary of Contents for KX-TVS90



























































































































































































































































































































































































































Reviews:

No comments

Related manuals for KX-TVS90

Brand: NEC Pages: 4

Brand: NEC Pages: 180

Brand: NEC Pages: 2

Brand: NEC Pages: 6

Brand: NEC Pages: 54

Brand: NEC Pages: 2

ELECTRA ELITE IPK II

Brand: NEC Pages: 174

DS2000 IntraMail

Brand: NEC Pages: 78

DS2000 IntraMail

Brand: NEC Pages: 6

Brand: NEC Pages: 268

Brand: Vadsbo Pages: 2

Brand: Facebook Pages: 5

Clear Sound CL455

Brand: Geemarc Pages: 64

Brand: CEECO Pages: 11

Brand: Uniden Pages: 64

Brand: GAI-Tronics Pages: 20

Brand: Interquartz Pages: 23

Brand: FunkTronic Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands